Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 186 / 1022

background image

Event Vector Table

4-40

ADSP-BF535 Blackfin Processor Hardware Reference

Table 4-11. Events That Cause Exceptions

Exception

EXCAUSE[5:0]

Type:
(E) error
(S) service
See note 1.

Notes/Examples

Force Exception
instruction

EXCPT

with

4-bit field m

m-field

S

Instruction provides 4 bits of

EXCAUSE

.

Single step

0x10

S

When the processor is in single step
mode, every instruction generates an
exception. Primarily used for debug-
ging.

Exception caused by
an emulation trace
buffer overflow

0x11

S

The processor takes this exception
when the trace buffer overflows (only
when enabled by the trace unit con-
trol register).

Undefined instruction

0x21

E

May be used to emulate instructions
that are not defined for a particular
processor implementation.

Illegal instruction
combination

0x22

E

See section for multi-issue rules in the

Blackfin Processor Programming Refer-
ence

.

Data access CPLB pro-
tection violation

0x23

E

Attempted read or write to supervisor
resource, or illegal data memory
access. Supervisor resources are regis-
ters and instructions that are reserved
for Supervisor use: Supervisor only
registers, all MMRs, and Supervisor
only instructions. (A simultaneous,
dual access to two MMRs using the
Data Address Generators generates
this type of exception.) In addition,
this entry is used to signal a protec-
tion violation caused by disallowed
memory access, and it is defined by
the Memory Management Unit
(MMU) cacheability protection loo-
kaside buffer (CPLB).

«
...
184
185
186
187
188
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Network Video Recorders

Бренд: e-Line Technology Страницы: 34

Бренд: National Instruments Страницы: 9

MegaRAID SCSI 320-2X

Бренд: LSI Страницы: 4

Бренд: FS Страницы: 19

Hollywood DV-Bridge

Бренд: Dazzle Страницы: 63

Бренд: Waves Страницы: 41

ZyXEL ZyAIR B-120

Бренд: ZyXEL Communications Страницы: 20

Бренд: Infoblox Страницы: 13

Бренд: ZyXEL Communications Страницы: 2

Бренд: ADLINK Technology Страницы: 108

Бренд: YASKAWA Страницы: 87

X570 AORUS ELITE WIFI

Бренд: Gigabyte Страницы: 48

Бренд: Commax Страницы: 122

Бренд: TRENDnet Страницы: 2

Бренд: Cambium Networks Страницы: 208

Бренд: MSI Страницы: 54

Бренд: Renesas Страницы: 6

Бренд: iSMA CONTROLLI Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды