Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 572 / 1022

background image

Device Mode Operation

13-10

ADSP-BF535 Blackfin Processor Hardware Reference

Inbound Transactions (ADSP-BF535 Processor as

PCI Target)

This section describes inbound transactions with the ADSP-BF535 pro-
cessor as the PCI target.

General Inbound Operation

To participate on a PCI bus as a target, the ADSP-BF535 processor must
first be configured. First, the processor core must write to the Memory
and I/O BAR Mask registers. Every bit set by the core in each of these
masks allows the corresponding bit in the memory base address register
(BAR) or I/O BAR, respectively, to be written by the PCI host during
configuration. The number of upper bits writable by the PCI determines
the size in bits of the base address register that configuration software on
the PCI side programs into the BAR. This determines the size of the win-
dow for which the PCI interface can claim the transaction as the intended
target.

Each bit of the mask registers must be set to 1 by the processor core, start-
ing with the uppermost bit (bit 31). To prevent the core from claiming
either memory or I/O transactions, the corresponding mask should be
programmed with all 0s (the default state). The pattern of all 1s is
assumed by the PCI interface to be contiguous, stray 0s make the bit non-
writable, and cause unpredictable results.

The processor core must also program the

PCI_TMBAP

and

PCI_TIBAP

regis-

ters. These registers are the base address pointers (BAPs) for incoming
memory and I/O transactions, respectively. The number of bits pro-
grammed into the upper portion of each of these registers must be the
same as the number of bits set in the corresponding mask. Any bits written
in the space where 0s exist in the mask are ignored, but the write to the
BAP completes successfully. If memory or I/O transactions are not
needed, then the corresponding BAP register is ignored and does not need
to be programmed. When the processor core has completed writing to

«
...
570
571
572
573
574
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Бренд: LaCie Страницы: 44

LaCie Ethernet Disk

Бренд: LaCie Страницы: 2

SATA II ExpressCard 34

Бренд: LaCie Страницы: 2

12big Rack Fibre 8

Бренд: LaCie Страницы: 9

xCORE-200 Multi-channel Audio board

Бренд: XMOS Страницы: 112

Бренд: Lancom Страницы: 70

Бренд: Kontron Страницы: 42

Бренд: Grundig Страницы: 24

Enterasys Matrix 2G4082-25

Бренд: Enterasys Страницы: 58

Бренд: Arduino Страницы: 25

SRA311-008P8 Series

Бренд: Divio Страницы: 4

Бренд: Aewin Technologies Страницы: 86

Бренд: Laser Страницы: 4

Homecraft Rolyan AA6240

Бренд: Patterson Страницы: 2

Бренд: Idis Страницы: 40

Бренд: Z3 Technology Страницы: 83

ControlCenter-IP 2.0

Бренд: G&D Страницы: 60

Бренд: FabiaTech Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды