Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 828 / 1022

background image

High Frequency Design Considerations

19-16

ADSP-BF535 Blackfin Processor Hardware Reference

Decoupling Capacitors and Ground Planes

Ground planes must be used for the ground and power supplies. The
capacitors should be placed very close to the

VDDEXT

and

VDDINT

pins of the

package as shown in

Figure 19-7

. Use short and fat traces for this. The

ground end of the capacitors should be tied directly to the ground plane
inside the package footprint of the processor (underneath it, on the bot-
tom of the board), not outside the footprint. A surface-mount capacitor is
recommended because of its lower series inductance.

Connect the power plane to the power supply pins directly with minimum
trace length. The ground planes must not be densely perforated with vias
or traces as their effectiveness is reduced. In addition, there should be sev-
eral large tantalum capacitors on the board.



Designs can use either bypass placement case shown in

Figure 19-6

or combinations of the two. Designs should try to minimize signal
feedthroughs that perforate the ground plane.

Oscilloscope Probes

When making high-speed measurements, be sure to use a “bayonet” type
or similarly short (< 0.5 inch) ground clip, attached to the tip of the oscil-
loscope probe. The probe should be a low-capacitance active probe
with 3 pF or less of loading. The use of a standard ground clip with
4 inches of ground lead causes ringing to be seen on the displayed trace
and makes the signal appear to have excessive overshoot and undershoot.
To see the signals accurately, a 1 GHz or better sampling oscilloscope is
needed.

«
...
826
827
828
829
830
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Transportation FiberinMotion

Бренд: Radwin Страницы: 122

Бренд: Samsung Страницы: 65

Бренд: Dahua Страницы: 6

Бренд: XMOS Страницы: 6

Бренд: Altera Страницы: 33

Бренд: Rimage Страницы: 30

MultiModem ISIHP-2S

Бренд: Multitech Страницы: 155

Бренд: Paradyne Страницы: 216

Dablet DVP 5000

Бренд: DarbeeVision Страницы: 10

Бренд: Iomega Страницы: 32

Бренд: MTI Страницы: 41

The DSX Value Solution (Japanese) LDX154

Бренд: ADC Страницы: 4

Бренд: ASROCK Страницы: 2

Zum ZUMMESH-NETBRIDGE

Бренд: Crestron Страницы: 2

Бренд: Icom Страницы: 7

Бренд: AJA Страницы: 129

Бренд: D-Link Страницы: 32

Бренд: D-Link Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды