Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 63 / 1022

background image

ADSP-BF535 Blackfin Processor Hardware Reference

1-9

Introduction

In addition, the PCI interface can either be used as a bridge from the pro-
cessor core as the controlling CPU in the system or as a host port where
another CPU in the system is the host and the ADSP-BF535 processor is
functioning as an intelligent I/O device on the PCI bus.

When the ADSP-BF535 processor acts as the system controller, it views
the PCI address spaces through its mapped windows. It can initialize all
devices in the system and maintain a map of the topology of the
environment.

The PCI memory region is a 4 Gbyte space that appears on the PCI bus
and can be used to map memory on I/O devices on the bus. The
ADSP-BF535 processor uses a 128 Mbyte window in memory space to see
a portion of the PCI memory space. A base address register positions this
window anywhere in the 4 Gbyte PCI memory space while its position
with respect to the processor addresses remains fixed.

The PCI I/O region is also a 4 Gbyte space; however, most systems and
I/O devices use only a 64 Kbyte subset of this space for I/O mapped
addresses. The ADSP-BF535 processor implements a 64 Kbyte window in
this space, along with a base address register that positions the window
anywhere in PCI I/O address space, while the window remains at the same
address in the processor address space.

PCI configuration space is a limited address space that is used for system
enumeration and initialization. It is a very low performance communica-
tion mode between the processor and PCI devices. The ADSP-BF535
processor provides a 1-value window to access a single data value at any
address in PCI configuration space. This window is fixed and receives the
address of the value, and the value if the operation is a write. Otherwise
the device returns the value into the same address on a read operation.

«
...
61
62
63
64
65
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

Бренд: GE Страницы: 4

INTERNET PRIVACY PROTECTION

Бренд: AlphaShield Страницы: 49

Бренд: Intel Страницы: 108

inLab Speedcure 9494800

Бренд: Dentsply Sirona Страницы: 91

Бренд: Barco Страницы: 121

Бренд: Rane Страницы: 128

Бренд: Acard Страницы: 34

Бренд: Shure Страницы: 113

Power System S914

Бренд: IBM Страницы: 48

Бренд: ADS Technologies Страницы: 21

Бренд: Xcellon Страницы: 24

Бренд: LST Страницы: 1

Бренд: SilverStone Страницы: 16

X-FireWire Card

Бренд: Apogee Страницы: 32

Бренд: WIN Enterprises Страницы: 25

Бренд: ADTRAN Страницы: 20

Бренд: IBM Страницы: 8

Бренд: ICP DAS USA Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды