Analog Devices ADSP-BF535 Blackfin Скачать руководство пользователя | Manualshive

Страница: 510 / 1022

background image

Multichannel Operation

11-64

ADSP-BF535 Blackfin Processor Hardware Reference

Window Size

The window size defines the range of the channels that can be enabled/dis-
abled in the current configuration. It can be any value in the range of 8 to
128, in increments of 8; the default value of 0 corresponds to a minimum
window size of 8 channels. Since the DMA buffer size is always fixed, it is
possible to define a smaller window size (for example, 32 bits), resulting in
a smaller DMA buffer size (in this example, 32 bits instead of 128 bits) to
save DMA bandwidth. The window size cannot be changed while the
SPORT is enabled.

Window Offset

The window offset specifies where in the 127-channel range to place the
start of the window. A value of 0 specifies no offset and permits using all
128 channels. As an example, a program could define a window with a
window size of 5 and an offset of 93. This 5-channel window would reside
in the range from 93 to 97. The window offset cannot be changed while
the SPORT is enabled.

If the combination of the window size and the window offset would place
the window outside of the range of the channel enable registers, none of
the channels in the frame are enabled, since this combination is invalid.

Other Multichannel Fields in SPORTx_TX_CONFIG,

SPORTx_RX_CONFIG

A multichannel frame contains more than one channel, as specified by the
window size and window offset; the multichannel frame is a combined
sequence of the window offset and the channels contained in the window.
The total number of channels in the frame is calculated by adding the
window size to the window offset.

«
...
508
509
510
511
512
...
»

Содержание ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-BF535 Blackfin

System x3630 M4

Бренд: IBM Страницы: 7

Бренд: Baicells Страницы: 8

Бренд: Paradyne Страницы: 11

Бренд: Paradyne Страницы: 19

COMSPHERE 3550 Series

Бренд: Paradyne Страницы: 153

Jetstream CPX-1000

Бренд: Paradyne Страницы: 141

Бренд: Samsung Страницы: 65

Бренд: STONEFLY Страницы: 48

Optane M Series

Бренд: Intel Страницы: 59

Бренд: DAD Страницы: 32

Бренд: Paradyne Страницы: 85

UM10301 PCA8565

Бренд: NXP Semiconductors Страницы: 54

Бренд: Advantech Страницы: 68

HHM Series HHM2409

Бренд: TDK Страницы: 2

POD-51EH-C541U-12

Бренд: IceTech Страницы: 8

Бренд: Intel Страницы: 154

Masterliquid ML240L RGB

Бренд: Cooler Master Страницы: 18

Бренд: ICP Страницы: 142

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды