manualshive.com logo in svg

Advanced Instruments OsmoPRO, Руководство пользователя

Поделиться
Скачать
Advanced Instruments OsmoPRO Скачать руководство пользователя страница 18

OsmoPRO MAX Automated Osmometer User Guide

18

NOTE: 

Read this chapter before you set up and use your 
instrument.

2.1  Electrical Requirements

Your instrument must be located within five feet of a 

properly grounded, three-prong electrical outlet 

capable of continuously supplying 1.0 amperes at 

100–240 VAC (50–60 Hz).

If the instrument is not grounded properly, its 

operation may be impaired and a safety hazard may 

exist. Verify that the outlet is appropriate before 

operating your instrument.

Do not disable the grounding plug.

NOTE: 

To get your OsmoPRO MAX up and running 
quickly as possible, Advanced Instruments 
recommends arranging to have an AI Service 
Technician onsite with you to assist with the 
installation and to answer your questions. Use 
the following contact information to schedule a 
service call:

•  US or Canada: 800-225-4034 from 8:00 AM – 

4:30 PM Eastern time

•  Outside US or Canada: +1 781-320-9000
•  Email: 

[email protected]

2.2  Select a Location for the Instrument

Select a location for the instrument based on the 
following space and electrical requirements.

Instrument Dimensions

The instrument dimensions are 14” (36 cm) W x 16.5” (42 cm) D 
x 18” (46 cm) H including containers for fluids and excluding 
the power cord, printer, and any USB peripherals.

Recommended Clearance

Allow 6 inches (15 cm) of clear space on each side of the 
instrument in order to access the peristaltic tubes on the 
left side and the power switch and connectors on the 
rear of the instrument.

Allow 6 inches (15 cm) of clear space behind the 
instrument in order to freely connect and disconnect the 
power cord and for fan-driven air circulation.

Do not block airflow from the exhaust fan on the back 
panel or underneath the instrument.

Recommended Bench Area

The typical bench area to hold the OsmoPRO MAX is 
16” W x 24” D.

2.3  Unpacking the Shipment

Carefully open the packaging, unpack your osmometer, 
accessories and supplies, and inspect them for shipping 
damage. 

• 

Use the enclosed packing list to verify receipt of 
items.

• 

Inspect the contents for damage.

• 

Save shipping material for future transport of the 
instrument.

• 

Complete the online warranty card to register the 
instrument (

www.aicompanies.com/warranty/

).

Reporting Missing or Damaged Items

• 

Missing items

: Notify your receiving department 

immediately. Advanced Instruments is responsible for 
missing items only if reported within 10 days of arrival.

• 

Damaged items:

 The insurer inspects shipping 

material.

 

–

Notify the dealer and Advanced Instruments within 
24 hours to ensure that your warranty and 
insurance can be applied.

 

–

Do not use any liquid items if the primary container 
has been damaged. Discard the product 
immediately.

 

–

Ask the transportation company to inspect the 
items, complete a 

Report of Concealed Damage,

 

and file your claim.

Chapter 2: 

Installation and Setup

Содержание OsmoPRO




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды