manualshive.com logo in svg

Advanced Instruments OsmoPRO, Руководство пользователя

Поделиться
Скачать
Advanced Instruments OsmoPRO Скачать руководство пользователя страница 12

Safe Use

OsmoPRO MAX Automated Osmometer User Guide

12

General Cautions

• 

For indoor use only. 

 

• 

The front barcode scanner uses a Class 2 laser. Do not stare directly into the beam when scanning  
barcodes. 

• 

Only power this instrument with the source specified on the product electrical ratings label. 
Refer to 

Power requirements

.

• 

If the power cord provided is replaced for any reason or if an alternate cord is used, the cord must be approved for use 
in the local country. The power cord must be approved for the product listed operating voltage and be rated at least 
20% greater than the volt-ampere (VA) ratings marked on the product’s electrical ratings label. The cord end that 
connects to the product must have an IEC 60320 connector.

• 

Plug the product into an approved grounded electrical outlet. Exposure to AC voltage could lead to electric shock, burn 
or electrocution. Please be aware of any exposure of AC voltage in the power cord.

• 

Do not disable the power cord grounding pin.

• 

If an extension cord or power strip is used, make sure that the cord or strip is rated for the product, and that the total 
ampere ratings of all products plugged into the extension cord or strip do not exceed 80% of the cord or strip rating 
limit.

• 

Route power cords so that they will not be walked on, tripped on, or pinched by items placed upon or against them. Pay 
particular attention to the plug, electrical outlet, and the point where the cord exits the product.

• 

Do not pull on cords and cables; grasp the corresponding connector to unplug it.

• 

Do not install or use this product in any area subject to extreme short-term temperature variations, or locations that 
exceed the specified operating environment temperatures.

• 

Never use this product in a wet area.

• 

To avoid injury or fire hazard, do not operate this product in an explosive atmosphere.

• 

Do not install or use the product on an unstable, non-level work surface.

• 

Never restrict airflow into or out of the product. Occasionally, check the air vents for blockage.

• 

Wipe the exterior of the product with a soft, damp cloth as needed. Using cleaning products other than those specified, 
may discolor or damage the finish (see 

Cleaning the instrument exterior

).

Содержание OsmoPRO




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды