THROTTLE BODIES
7-12
1. Install new seals onto the end of each injec-
tor.
2. Install the fuel injectors to the fuel rail.
3. Install the fuel injector assemblies to the
throttle bodies.
4. Check the injector pressure after the fuel in-
jectors are installed to the throttle bodies.
Refer to “CHECKING THE INJECTOR
PRESSURE” on page 7-12.
EAS30481
CHECKING THE INJECTOR PRESSURE
TIP
• After installing the fuel injectors, perform the
following steps to check the injector pressure.
• Do not allow any foreign materials to enter the
fuel lines.
1. Check:
• Injector pressure
a. Connect the fuel injector pressure adapter
“1” to the fuel rail “2”, and then connect an
air compressor “3” to the adapter.
b. Connect the pressure gauge “4” to the fuel
injector pressure adapter “1”.
c. Close the valve on the fuel injector pres-
sure adapter.
d. Apply air pressure with the air compres-
sor.
e. Open the valve on the fuel injector pres-
sure adapter until the specified pressure is
reached.
NOTICE
ECA18440
Never exceed the specified air pressure or
damage could occur.
f. Close the valve on the fuel injector pres-
sure adapter.
g. Check that the specified air pressure is
held for about one minute.
Pressure drops
→
Check the pressure
gauge and adapter.
Check the seals and O-rings, and then re-
install.
Replace the fuel injectors.
EAS30482
CHECKING THE FUEL PRESSURE
1. Remove:
• Rider seat
Refer to “GENERAL CHASSIS (1)” on page
4-1.
• Fuel tank side covers
Refer to “GENERAL CHASSIS (3)” on page
4-5.
2. Check:
• Fuel pressure
a. Remove the rear fuel tank mounting
bracket bolts “1” and quick fasteners “2”,
and then holdup the fuel tank.
NOTICE
ECA23360
When lifting up the fuel tank, be careful not
to pull the fuel tank breather/overflow hose.
b. Disconnect the fuel hose “3” from the fuel
tank.
T
R
.
.
Fuel rail bolt
3.5 N·m (0.35 kgf·m, 2.6 lb·ft)
Pressure gauge
90890-03153
Pressure gauge
YU-03153
Fuel injector pressure adapter
90890-03210
Fuel injector pressure adapter
YU-03210
G0
8
9041
Specific air pressure
490 kPa (4.9 kgf/cm
2
, 69.7 psi)
2
1
1
Summary of Contents for Tenere 700 2020
