Whirlpool ADVANTECH CAE2761K Installation, Operation And Service Instructions Download Page 99

Page: 99 / 178

4-41

REMOVING THE UPPER DRYER

Unplug dryers or disconnect power.

Turn off gas supply to dryers.

Remove the console (see step 3 on page
4-35 for the procedure).

Remove the money acceptors (see page
4-38 for the procedure).

Remove the cotter pins (if installed) from
the two front security bolts.

Cotter Pin

Security Bolt

Remove the upper dryer’s lower service
access panel.

Clip

Lower Service

Access Panel

Pry

Down

Clip

Continued on the next page.

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before
operating.

Failure to do so can result in death or
electrical shock.

WARNING

Remove the two front security bolts and
flat washers from the upper dryer.

Front Security Bolts & Flat Washers

Disconnect the main harness connector
from the top of the collar.

Main Harness Connector

Summary of Contents for ADVANTECH CAE2761K



















































































































































































Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands

Whirlpool ADVANTECH CAE2761K, Installation, Operation And Service Instructions

Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands