Whirlpool ADVANTECH CAE2761K Installation, Operation And Service Instructions Download Page 125

Page: 125 / 178

5-11

THERMAL FUSE

Refer to page 4-45 for the procedure for ser-
vicing the thermal fuse.

Electric Dryers:

The thermal fuse is wired in

series with the drive motor. If the thermal fuse
opens, 91

C (196

F), power to the motor is

turned off. A centrifugal switch on the motor
also opens the heater circuit.

Once the thermal fuse has opened, it will not
reset, and must be replaced. Check for a failed
operating thermostat, or a shorted heater ele-
ment.

Gas Dryers:

The thermal fuse is wired in

series with the gas valve. If the thermal fuse
opens, 91

C (196

F), power to the valve is

turned off. A centrifugal switch on the motor
also opens the heater circuit.

Once the thermal fuse has opened, it will not
reset, and must be replaced. Check for a failed
operating thermostat.

Blower
Housing

Thermal Fuse
91

C (196

1. Unplug dryer or disconnect power.

2. Turn off gas supply to dryer.

3. Disconnect the wires from the thermal fuse.

4. Set the ohmmeter to the R X 1 scale.

5. Touch the ohmmeter test leads to the ther-

mal fuse terminals. The meter should indi-
cate continuity (0

Ω

). If the meter indicates

an open circuit (infinite), replace the ther-
mal fuse.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

Summary of Contents for ADVANTECH CAE2761K



















































































































































































Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands

Whirlpool ADVANTECH CAE2761K, Installation, Operation And Service Instructions

Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands