Whirlpool ADVANTECH CAE2761K Installation, Operation And Service Instructions Download Page 101

Page: 101 / 178

4-43

REMOVING THE COLLAR ASSEMBLY

Unsnap the female main harness connec-
tor from the collar bracket.

Clip the wire tie from the main harness and
power supply cord.

Remove the four 1/4

″

hex-head screws

from the collar flange.

Remove the two 1/2

″

hex-head bolts from

the collar studs.

Lift the collar assembly off the lower dryer.

Female
Connector

Wire Tie

Left Collar
Screws

Right Collar
Screws

Unplug dryers or disconnect power.

Turn off gas supply to dryers.

Remove the upper dryer (see page 4-41
for the procedure).

Collar Assembly

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before
operating.

Failure to do so can result in death or
electrical shock.

WARNING

Collar Studs For 1/2

″

Hex-Head Bolts

Summary of Contents for ADVANTECH CAE2761K



















































































































































































Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands

Whirlpool ADVANTECH CAE2761K, Installation, Operation And Service Instructions

Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands