Whirlpool ADVANTECH CAE2761K Installation, Operation And Service Instructions Download Page 75 | Manualshive

Page: 75 / 178

background image

4-17

9.

Lift the cabinet slightly and tip it forward on
its front edges.

IMPORTANT:

The cabinet

will not stand on its own in the upright
position.

Side Rail

Alignment Tab

NOTE:

Tension can be added to the cabinet

clips to insure better frame-to-cabinet fit by
adjusting the clips. Apply pressure in the direc-
tion of the arrow while holding the clip in the
pliers. Another method is to install kit

#488495

.

NOTE:

You can remove the right and left side

panels of the cabinet, instead of removing the
complete cabinet assembly. However, you will
have to remove the front panel first.

REASSEMBLY NOTE:

When you reinstall the

cabinet,  make  sure  that  the  small  alignment
tabs at the front and rear of each side rail are
fully  upright,  as  shown  below,  and  not  bent
over.  Also  make  sure  that  the  side  rails  are
straight and not deformed, otherwise, the cabi-
net will not fit properly.

Damaged Bottom
Cabinet Flange

Properly Aligned
Bottom Cabinet Flange

Plastic Lock

«
...
73
74
75
76
77
...
»

Summary of Contents for ADVANTECH CAE2761K



















































































































































































Reviews:

No comments

Related manuals for ADVANTECH CAE2761K

Built-In Dishwasher

Brand: GE Pages: 32

Brand: NEFF Pages: 52

Brand: Lavorwash Pages: 28

Brand: Rac Pages: 11

HDS 645-4 M Basic

Brand: Kärcher Pages: 328

Brand: Ardo Pages: 14

Brand: Zanussi Electrolux Pages: 24

Brand: Saivod Pages: 76

Brand: Progress Pages: 64

Brand: Briggs & Stratton Pages: 3

Brand: NEFF Pages: 60

Brand: Lett Pages: 97

Brand: inventum Pages: 108

Brand: Haier Pages: 34

Brand: Haier Pages: 20

Brand: Haier Pages: 42

Brand: Haier Pages: 20

HW100-DM14876TNZP

Brand: Haier Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands