Whirlpool ADVANTECH CAE2761K Installation, Operation And Service Instructions Download Page 166 | Manualshive

Page: 166 / 178

background image

A quencher is located in the wiring harness near the water level switch on the washer and screwed to the cabinet of the
gas dryer in front of the burner assembly. The quenchers are designed to reduce EMI from the water level switch or gas
valve when they change state. EMI generated from a switch state change may cause the electronic control to reset during
a cycle when a quencher has failed or has been removed.

Kit 3952286 is designed to replace the water level switch quencher on EMS1000 washers built prior to 1999. Starting with
1999 production the water level switch quencher is integral to the wiring harness necessitating harness replacement for
quencher failure.

SUPRESSOR QUENCHER APPLICATION TABLE

PRODUCT

SUPRESSOR LINE IN, PART NUMBER

AND LOCATION

QUENCHER

PART NUMBER AND LOCATION

EMS1000
WASHERS
PRIOR TO 1999

3951390 Located between power cord
plug and wiring harness plug

3952286 on water level switch in
console

EMS1000 AND
ADVANTECH™
WASHERS
AFTER 1999

1999 and after in harness near water
level switch connection, harness must
be replaced if quencher fails

EMS1000 AND
ADVANTECH™
GAS DRYERS

3406196 Located in the console behind
the power cord access panel

located in the wiring harness near the
gas valve, harness must be replaced if
quencher fails

EMS1000 AND
ADVANTECH™
ELECTRIC DRYERS

3406197 Located at the black and white
harness plug near the power cord
terminal block

QUENCHER REPLACEMENT EMS1000 WASHERS PRIOR TO 1999 WITH WATER LEVEL SWITCH
IN THE CONSOLE

1.

Unplug the washer from the AC outlet.

2.

Remove the screws from the front bottom of the console and rotate the console up into the service position.

3.

Disconnect the violet wire with the white stripe from the pressure switch.

4.

Connect either quencher wire into the pressure switch where the violet wire with the white stripe was removed.

5.

Reconnect the violet wire with the white stripe to the piggyback connector on the quencher wire.

6.

Disconnect the pink wire from the pressure switch.

— 2 —

(continued)

«
...
164
165
166
167
168
...
»

Summary of Contents for ADVANTECH CAE2761K



















































































































































































Reviews:

No comments

Related manuals for ADVANTECH CAE2761K

Brand: GE Pages: 2

Brand: Haier Pages: 6

Brand: Haier Pages: 6

Brand: Haier Pages: 24

Brand: Haier Pages: 12

Brand: Haier Pages: 12

Brand: Haier Pages: 23

Brand: Haier Pages: 12

Brand: Belling Pages: 18

Brand: Labconco Pages: 72

Brand: F.F. Group Pages: 76

Brand: Hotpoint Pages: 16

Brand: Michelin Pages: 40

Brand: Magic Chef Pages: 42

Brand: Tisira Pages: 32

KUD-WC1113KUD-WD1117

Brand: Unique Klasse Pages: 54

Brand: Porter-Cable Pages: 20

Brand: Hanseatic Pages: 78

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands