Whirlpool ADVANTECH CAE2761K Installation, Operation And Service Instructions Download Page 93

Page: 93 / 178

4-35

Stack Dryers

REMOVING THE CONSOLE COMPONENTS

To remove the console:

a) Unlock the console, pull the right side

out, and remove the console from the
unit so you can access the wiring.

Console

Console Lock

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before
operating.

Failure to do so can result in death or
electrical shock.

WARNING

Unplug dryers or disconnect power.

Turn off gas supply to dryers.

Continued on the next page.

b) Disconnect the two P1 connectors for

the upper and lower dryers from the
display boards.

c) Remove the 5/16

″

hex-head screw from

the console securing the red retaining
wire and green ground wire.

P1 Connectors

Display Boards

Ground Screw

Summary of Contents for ADVANTECH CAE2761K



















































































































































































Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands

Whirlpool ADVANTECH CAE2761K, Installation, Operation And Service Instructions

Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands