Whirlpool ADVANTECH CAE2761K Installation, Operation And Service Instructions Download Page 38

Page: 38 / 178

2-24

MOVING THE DRYER

Gas Dryers

1. Unplug dryer or disconnect power.

2. Turn off gas supply to dryer.

3. Disconnect the gas pipe and fittings from

the dryer, then cap the gas supply line.

4. Tape the open end of the dryer gas pipe.

5. Make sure the leveling legs are secure in

the dryer base.

6. Tape the dryer door and the lint screen.

Electric Dryers

1. Unplug dryer or disconnect power.

2. Disconnect the power supply cord or cable

from the dryer terminal block.

3. Make sure the leveling legs are secure in

the dryer base.

4. Tape the dryer door and the lint screen.

MAINTENANCE INSTRUCTIONS

1. Clean the lint screen after each cycle.

2. Keep the dryer area clear and free of com-

bustible materials, gasoline, and other flam-
mable vapors and liquids.

3. Do not obstruct the flow of combustion and

ventilation air from inside the dryer cabinet.

4. Lint should be removed from the ducting

every two years, or more often depending
on dryer usage.

Summary of Contents for ADVANTECH CAE2761K



















































































































































































Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands

Whirlpool ADVANTECH CAE2761K, Installation, Operation And Service Instructions

Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands