Whirlpool ADVANTECH CAE2761K Installation, Operation And Service Instructions Download Page 82

Page: 82 / 178

4-24

To remove the water level switch:

a) Press the locking tab on the water level

switch, then rotate the switch in either
direction until the square extrusion
aligns with the cutout in the rear panel,
and remove the switch.

b) Disconnect the air hose and wire connec-

tor from the switch.

Locking
Tab

Turn 90

Water Level Switch

Air Hose

Wire
Connector

5/16

″

Screw

Tab

Drain Hose

d) Pull the drain hose off the drain hose

assembly.

To remove the drain hose assembly:

a) Remove the 5/16

″

hex-head screw from

the drain hose assembly.

b) Tilt the cabinet forward to lift the rear of

the unit.

c) Reach under the unit and gently pull

down on the drain hose assembly lock-
ing tab, and push the assembly out
through the rear panel.

Dran Hose

Assembly

Drain Hose

Assembly

Locking
Tab

Summary of Contents for ADVANTECH CAE2761K



















































































































































































Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands

Whirlpool ADVANTECH CAE2761K, Installation, Operation And Service Instructions

Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands