Whirlpool ADVANTECH CAE2761K Installation, Operation And Service Instructions Download Page 96

Page: 96 / 178

4-38

REMOVING THE MONEY ACCEPTORS

Unplug dryers or disconnect power.

Turn off gas supply to dryers.

Remove the console (see step 3 on page
4-35 for the procedure).

To remove the coinslide assembly:

a) Using a 5/16

″

socket, unscrew the re-

taining bolt from the money acceptor,
and remove the bolt from inside the
console opening.

Coinslide Retaining Bolt

b) Lift the coinslide and pull it forward out

of the unit.

c) Unplug the two wires from the coinslide

switch.

d) Remove the ground wire screw from

the bottom of the coinslide assembly.

Coinslide Switch
With 2 Wires

Coinbox

Coinslide

Coinbox

Coindrop

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before
operating.

Failure to do so can result in death or
electrical shock.

WARNING

Example Of Various Money Acceptor Configurations

Summary of Contents for ADVANTECH CAE2761K



















































































































































































Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands

Whirlpool ADVANTECH CAE2761K, Installation, Operation And Service Instructions

Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands