Whirlpool ADVANTECH CAE2761K Installation, Operation And Service Instructions Download Page 77

Page: 77 / 178

4-19

To remove the outer tub:

a) Remove the end of the counterbal-

ance spring from the hole in the frame.

NOTE:

The end of the spring is con-

nected to the base assembly. The
washer in the photo below is shown
laying on its rear panel.

c) Tap the bottom of the drive block with

a hammer and remove it from the bas-
ket drive shaft.

DRIVE BLOCK REASSEMBLY NOTE:

When

you reinstall the drive block on the basket drive,
make sure that you align the two slots in the
drive block with the corresponding tabs on the
top of the basket drive shaft. If they are mis-
aligned, the basket drive and drive block will fail.

Drive Block

Tabs Flush
With Top
Surface
Of Drive
Block

Slots In Drive Block

Tabs On Basket Drive

b) Disconnect the end of the water level

hose from the side of the outer tub.

Drain Hose

Counterbalance Spring

Base Assembly

Water Level Hose

(Viewed From Bottom Of Unit)

Air Dome

Continued on the next page.

Summary of Contents for ADVANTECH CAE2761K



















































































































































































Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands

Whirlpool ADVANTECH CAE2761K, Installation, Operation And Service Instructions

Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands