Whirlpool ADVANTECH CAE2761K Installation, Operation And Service Instructions Download Page 64

Page: 64 / 178

4-6

REMOVING THE MONEY ACCEPTORS & METERCASE

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before
operating.

Failure to do so can result in death or
electrical shock.

WARNING

Unplug washer or disconnect power.

Unlock the service access door and re-
move it from the top of the metercase.

Coinslide
Assembly

Coinbox

Metercase

Access Door

Coinslide Switch

(inside) On

Coinslide

Extension

To remove the coinslide assembly:

a) Using a 5/16

″

socket, unscrew the

retaining bolt from the money accep-
tor, and remove the bolt from inside the
metercase.

b) Remove the 5/16

″

hex-head screw from

the coinslide green ground wire that is
attached inside the metercase.

5/16

″

Retaining Bolt

Ground Wire

Summary of Contents for ADVANTECH CAE2761K



















































































































































































Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands

Whirlpool ADVANTECH CAE2761K, Installation, Operation And Service Instructions

Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands