Whirlpool ADVANTECH CAE2761K Installation, Operation And Service Instructions Download Page 86

Page: 86 / 178

4-28

c) If a mounting stud is not installed on the

new end cap, remove the stud from the
old cap, and install it on the new one.

Left End

Cap

Mounting Stud

b) Remove the two hex-head screws from

the console support bracket, and slide
the end cap off the end of the panel.

Console Support
Bracket Screws

To remove an end cap from the console:

a) Remove the hex-head screw from the

rear of the end cap.

Left End

Cap

Rear Screw

b) Remove the two screws from the card

reader assembly and remove the as-
sembly.

Card Reader Screws

Card Reader Assembly

To remove the card reader assembly
on a full console machine:

a) Disconnect the connector from the

ADVANTECH



control board at P11.

Card Reader

P11

ADVANTECH



Control Board

Summary of Contents for ADVANTECH CAE2761K



















































































































































































Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands

Whirlpool ADVANTECH CAE2761K, Installation, Operation And Service Instructions

Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands