Whirlpool ADVANTECH CAE2761K Installation, Operation And Service Instructions Download Page 113

Page: 113 / 178

4-55

REMOVING THE OUTLET GRILLE

Unplug dryer(s) or disconnect power.

Turn off gas supply to dryer(s).

Open the dryer door and remove the lint
filter screen.

Remove the three inside screws from the
outlet grille.

Outlet Grille Screws

Lint Filter

Screw

Outlet Grille

Remove the two front screws from the
outlet grille.

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before
operating.

Failure to do so can result in death or
electrical shock.

WARNING

Summary of Contents for ADVANTECH CAE2761K



















































































































































































Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands

Whirlpool ADVANTECH CAE2761K, Installation, Operation And Service Instructions

Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands