Whirlpool ADVANTECH CAE2761K Installation, Operation And Service Instructions Download Page 41

Page: 41 / 178

2-27

COlNSLIDE INSTALLATION,
CSP STACK DRYERS

NOTE:

Make sure that all wiring harness con-

nections are secure prior to closing the console
after servicing or installing money acceptors.

4. Perform steps 4 through 7 on page 2-26.

NOTE:

A stacked dryer uses collar open-

ings for money acceptors instead of a
metercase.

5. Make sure all harness connections are

properly connected and reinstall the con-
sole.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before
operating.

Failure to do so can result in death or
electrical shock.

Follow these instructions to ensure proper elec-
trical grounding of the coinslide unit.

1. Unplug or disconnect electrical power.

2. Unlock the cam lock on the right side of the

console.

3. To remove the console, pull the right end

out, and slide it away from the collar.

Summary of Contents for ADVANTECH CAE2761K



















































































































































































Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands

Whirlpool ADVANTECH CAE2761K, Installation, Operation And Service Instructions

Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands