Whirlpool ADVANTECH CAE2761K Installation, Operation And Service Instructions Download Page 98

Page: 98 / 178

4-40

REMOVING THE ADVANTECH



CONTROL BOARDS

Unplug dryers or disconnect power.

Turn off gas supply to dryers.

Remove the console (see step 3 on page
4-35 for the procedure).

Screw (1 of 6)

Relays

P11

Ground Wire

ADVANTECH



Control Board

ADVANTECH



Control Board—Upper Dryer

Disconnect the board connectors at P1,
P4, P8, and P11.

Disconnect the four wires at the dryer
motor relay K3 (RD & RD), and dryer
heater relay K2 (BU & BK).

Disconnect the green ground wire from
terminal P6.

Remove the six 5/16

″

hex-head screws

from the board and remove the board.

ADVANTECH



Control Board—Lower Dryer

(Viewed From Top With Upper Dryer Removed)

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before
operating.

Failure to do so can result in death or
electrical shock.

WARNING

FRONT OF UNIT

Summary of Contents for ADVANTECH CAE2761K



















































































































































































Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands

Whirlpool ADVANTECH CAE2761K, Installation, Operation And Service Instructions

Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands