Whirlpool ADVANTECH CAE2761K Installation, Operation And Service Instructions Download Page 168 | Manualshive

Page: 168 / 178

background image

SUPRESSOR REPLACEMENT EMS1000 and ADVANTECH™ WASHERS

1.

Remove the 2 control panel screws at the base of the console and rotate the console open into the service position.

2.

Remove the electrical tape that secures the suppressor/quencher assembly to the wiring harness.

3.

Unplug the suppressor from the power cord connector and the wiring harness connector.

NOTE: On washers it is possible to plug the wiring harness connector directly into the power cord connector BYPASSING
the suppressor. On dryers the unit will operate without the suppressor plugged in. This will expose the control to line
transients (voltage spikes) that can damage the control. Internal switch closures may also cause the control to reset.
NEVER eliminate the supressor or quencher!

SUPRESSOR REPLACEMENT 27” EMS1000 and ADVANTECH™ DRYERS

1.

Disconnect electrical power.

2.

On gas dryers remove the power cord access panel from the rear of the dryer.

3.

Remove the power cord from the backsplash.

4.

On electric dryers remove the control panel mounting screws and rotate the console open into the service position.

5.

Unplug the suppressor from the power cord and wiring harness and replace.

6.

Replace all panels and reconnect electrical power.

NOTE: On 29” Dryers remove the rear access panel to gain access to the suppressor assembly located underneath the
terminal block.

SUPPRESSOR

HARNESS AND

POWER CORD

CONNECTORS

SUPPRESSOR

BYPASSED

UNPLUG

SUPPRESSOR AT

POWER CORD AND

HARNESS

CONNECTION

— 4 —

«
...
166
167
168
169
170
...
»

Summary of Contents for ADVANTECH CAE2761K



















































































































































































Reviews:

No comments

Related manuals for ADVANTECH CAE2761K

Brand: Ignis Pages: 28

Brand: Dacor Pages: 29

Brand: lamber Pages: 52

SUNJOE SPX9006-PRO

Brand: SNOWJOE Pages: 20

Brand: Zanussi Electrolux Pages: 19

Brand: Philco Pages: 192

Brand: Greencut Pages: 52

PowerPlus GardenPro POWXG90425

Brand: VARO Pages: 9

Brand: Kärcher Pages: 256

KUD-WC1113KUD-WD1117

Brand: Unique Klasse Pages: 54

Brand: Hotpoint Pages: 20

Brand: Euromaid Pages: 29

Brand: Daewoo Pages: 7

Brand: Klarstein Pages: 168

HD 2.0/1000 Dual Mister Cart

Brand: Kärcher Pages: 21

Brand: Hotpoint Pages: 20

3VT541XD - annexe 3

Brand: BALAY Pages: 30

Brand: Maytag Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands