Whirlpool ADVANTECH CAE2761K Installation, Operation And Service Instructions Download Page 66

Page: 66 / 178

4-8

To remove the coindrop assembly:

a) From inside the open access panel of

the metercase, remove the screws or
hex-bolts from the back of the coindrop
assembly.

b) Position the console to its service po-

sition (see page 4-2 for the procedure).

c) Disconnect the connector(s) at P10 /

COIN 1 (& P12 / COIN 2) on the
ADVANTECH



control board.

To remove the coinbox switch:

a) Unlock and remove the coinbox from

the metercase.

b) Disconnect the two wires from the

coinbox switch terminals from inside
the metercase.

c) Squeeze the locking tabs on the top

and bottom of the switch body and
push the switch into the coinbox com-
partment of the metercase.

P12 (COIN 2)

ADVANTECH



Control Board

P10 (COIN 1)

d) Remove the coindrop with its wire har-

ness from the unit.

Coindrop

Assembly

Top Locking Tab

Coinbox Switch Wires

Summary of Contents for ADVANTECH CAE2761K



















































































































































































Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands

Whirlpool ADVANTECH CAE2761K, Installation, Operation And Service Instructions

Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands