Whirlpool ADVANTECH CAE2761K Installation, Operation And Service Instructions Download Page 53

Page: 53 / 178

2-39

CONTROL SETUP:
HANDHELD PALM



(PDA) DEVICE

Detailed Palm



enabled set up information can

be obtained from the Software User's Manual,
Part

#8524743

This section will cover the installation of a
template from the Palm



to a washer or dryer.

For advanced features such as template cre-
ation requiring use of the management soft-
ware, see the Software User’s Manual, Part

#8524743

NOTE:

The following procedure assumes that

security, locations and templates have already
been established using the management soft-
ware program and that the selected Palm



has

performed a

HotSync



with the management

software.

1. To start the Handheld Software, remove

the Palm



handheld from its cradle and turn

it on.

2. Check the battery power by pressing the

HOME button with the stylus. 50% or more
battery power is needed.

3. Using the stylus, tap the Palm



handheld,

and scroll to the ADVANTECH



icon.

4. Tap the ADVANTECH



icon.

5. The

Welcome

screen will appear.

6. Tap on

Continue

7. The

Login

screen appears.

8. Select the correct

Servicer ID

, and enter

the corresponding

password

using the

Graffiti



writing method.

9. Tap on

Continue

. The

Select a location

window appears. Select the appropriate

location

, then tap on

Continue

10. After logging in and selecting the appropri-

ate location, the

Select a command

screen

appears.

Summary of Contents for ADVANTECH CAE2761K



















































































































































































Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands

Whirlpool ADVANTECH CAE2761K, Installation, Operation And Service Instructions

Search results

Summary of Contents for ADVANTECH CAE2761K

Reviews:

Related manuals for ADVANTECH CAE2761K

Brands by name

Popular brands