Westlock ICoT 5500 Installation & Operating Manual Download Page 91

Page: 91 / 206

WESTLOCK CONTROLS CORPORATION

280 N. MIDLAND AVE., STE. 258, SADDLE BROOK, NJ 07663 TEL: 201-794-7650 FAX: 201-794-0913

www.westlockcontrols.com

10/5/2013

TECH-477/D.W.O. 21424

Page 91 of 206

Software Revision: Firmware version
Hardware Revision:

Electronic board version

PROFIBUS Ident Number: Device Ident number in use. The hexadecimal number

0E88 is the specific identification number assigned to ICoT
PA.

Profile:

PROFIBUS profile class. ICoT has PROFIBUS PA, Compact Class B.

Profile Revision:

3.02 – ICoT is compatible with profile 3.02

HW Write Protection:

This parameter shows the status of hardware write protection.

The board has a dipswitch named SW4, where is possible to set the
hardware write protection.

Write Locking:

Set the write protection by software.

Local Operation:

Enable or disable the local operation via keypad.

9.3.2 Transducer

Located under Parameters this directory is divided in many sub directories where is
possible to configured and calibrate the device.

9.3.2.1 Basic Setup

A sub directory of Parameters/Transducer, it has a group of initial configuration
parameters.

Summary of Contents for ICoT 5500















































































































































































































Search results

Summary of Contents for ICoT 5500

Reviews:

Related manuals for ICoT 5500

Brands by name

Popular brands

Westlock ICoT 5500, Installation & Operating Manual

Search results

Summary of Contents for ICoT 5500

Reviews:

Related manuals for ICoT 5500

Brands by name

Popular brands