Westlock ICoT 5500 Installation & Operating Manual Download Page 129 | Manualshive

Page: 129 / 206

background image

WESTLOCK CONTROLS CORPORATION

280 N. MIDLAND AVE., STE. 258, SADDLE BROOK, NJ 07663 TEL: 201-794-7650 FAX: 201-794-0913

www.westlockcontrols.com

10/5/2013

TECH-477/D.W.O. 21424

Page 129 of 206

DD Reference: Consists of Manufacturer Code, the Device Type,

the Device Revision and the Revision of the Device
Description.

DD Revision: Revision of the Device Description.

Profile: PROFIBUS profile class. ICoT has PROFIBUS PA,

Compact Class B.

Profile Revision: 3.02 – ICoT is compatible with profile 3.02

Execution Time: Parameter is reserved for future use and contains

no relevant data.

Number of Parameters: Number of used indices (parameters of a block

including the non-implemented optional parameters.

Index of VIEW 1: The index of the View 1.

Number of View Lists: Number of view lists defined in a block.

General

Static Revision No.: The revision level of the static data associated with

the block. The Static Revision No. is changed by the
device each time data are written to the static
parameter.

TAG: Physical device tag.

Strategy: The strategy field can be used to help group blocks.

Alert Key: The alert parameter (0 – 255) has a user-assigned

value which may be used in sorting alarms or
events generated by a block.

Block Modes

Target Mode: Sets the desired mode for the block. The input

parameters of the block in conjunction with the state
of the block are used to determine if the block can
achieve the requested target mode. The automatic
modes used in this profile are Auto and RCAS. The
manual modes are LO and Man. In O/S mode, the
normal algorithm is no longer executed.

Actual Mode: Indicates the current mode of operation the block is

able to achieve.

Permitted Mode: Defines the modes which are allowed in this

instance of the block.

Normal Mode: The mode which the block uses during normal

operation conditions.

Alarm Summary

Current State Alarm Sum: The alarm sum of the current alarm state.

Unacknowledged State Alarm

Sum:

The alarm sum of the unacknowledged alarm state.

Unreported Stated Alarm Sum: Unreported State Alarm Sum.

«
...
127
128
129
130
131
...
»

Summary of Contents for ICoT 5500















































































































































































































Reviews:

No comments

Related manuals for ICoT 5500

Brand: Bancroft Pages: 12

Brand: Lang Pages: 58

Brand: Bosch Pages: 36

Brand: Bosch Pages: 32

Brand: Bosch Pages: 40

The Rook CryoAdvance 100

Brand: Montana Instruments Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands