Westlock ICoT 5500 Installation & Operating Manual Download Page 108 | Manualshive

Page: 108 / 206

background image

WESTLOCK CONTROLS CORPORATION

280 N. MIDLAND AVE., STE. 258, SADDLE BROOK, NJ 07663 TEL: 201-794-7650 FAX: 201-794-0913

www.westlockcontrols.com

10/5/2013

TECH-477/D.W.O. 21424

Page 108 of 206

9.6.3 Alarm AI

Located under Diagnosis, it has a group of parameters to read and configure the upper
and lower alarms and warnings.

ALARM_HYS

Limit Hysteresis: Hysteresis expressed in the engineering units of the output

value scale. An alarm occurs when a value exceeds an
upper limit. The alarm’s status remains true until the value
drops below the limit minus the alarm hysteresis. The
directions are reversed for low limit detection. The
hysteresis is also used for warnings.

Alarm/Warning Limits

Upper Limit Alarm: Upper alarm limit in engineering units.

Upper Limit Warning: Upper warning limit in engineering units.
Lower Limit Warning: Lower warning limit in engineering units.

Lower Limit Alarm: Lower alarm limit in engineering units.

HI_HI_ALM

Unacknowledged Alarms: Unacknowledged alarms.

Status: Status for the upper alarm.

Time Stamp: The time of day when a change in limit stated was

detected that was unreported.

Cause: Cause of the upper alarm.

Alarm Output Value: Output value at the time of the upper alarm.

«
...
106
107
108
109
110
...
»

Summary of Contents for ICoT 5500















































































































































































































Reviews:

No comments

Related manuals for ICoT 5500

Brand: Incra Pages: 8

Brand: YASKAWA Pages: 104

Brand: Becker Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands