Westlock ICoT 5500 Installation & Operating Manual Download Page 161

Page: 161 / 206

WESTLOCK CONTROLS CORPORATION

280 N. MIDLAND AVE., STE. 258, SADDLE BROOK, NJ 07663 TEL: 201-794-7650 FAX: 201-794-0913

www.westlockcontrols.com

10/5/2013

TECH-477/D.W.O. 21424

Page 161 of 206

current valve position.

Setpoint: Analog output set point.

Value Position: This parameter show if the valve is one of the limits or it is

an intermediate point. The valid values for it are:
1: Closed
2: Opened
3: Intermediate Position

Check back This parameter is not implemented.

10.4.4 Output

(AO)

Located at fourth tab of Process Variable && Trend curves, this tab displays as bar
graph the values of following Analog output (AO) block parameters: output and
checkback.

output Value: Output Analog output feedback. This parameter will be use

as setpoint for the transducer.

Check back This parameter is not implemented.

Summary of Contents for ICoT 5500















































































































































































































Search results

Summary of Contents for ICoT 5500

Reviews:

Related manuals for ICoT 5500

Brands by name

Popular brands

Westlock ICoT 5500, Installation & Operating Manual

Search results

Summary of Contents for ICoT 5500

Reviews:

Related manuals for ICoT 5500

Brands by name

Popular brands