Toshiba TMPM3V4 Manual Download Page 347

Page: 347 / 544

14.5 SSP operation

14.5.1 Initial setting for SSP

Settings for the SSP communication protocol must be made with the SSP disabled.

Control registers SSPCR0 and SSPCR1 need to configure this SSP as a master or slave operating under

one of the following protocols. In addition, make the settings related to the communication speed in the

clock prescale registers SSPCPSR and SSPCR0 <SCR>.

This SSP supports the following protocols:

・

SPI

・

SSI

・

Microwire

14.5.2 Enabling SSP

The transfer operation starts when the operation is enabled with the transmitted data written in the trans-

mit FIFO, or when transmitted data is written in the transmit FIFO with the operation enabled.

However, if the transmit FIFO contains only four or fewer entries when the operation is enabled, a trans-

mit interrupt will be generated. This interrupt can be used to write the initial data.

Note:

When the SSP is in the SPI slave mode and the SPFSS pin is not used, be sure to transmit data of

one byte or more in the FIFO before enabling the operation. If the operation is enabled with the trans-

mit FIFO empty, the transfer data will not be output correctly.

14.5.3 Clock ratios

When setting a frequency for fsys , the following conditions must be met.

・

In master mode

SPCLK

(maximum) → f

sys

SPCLK

(minimum) → f

sys

/(254×256)

・

In slave mode

SPCLK

(maximum) → f

sys

/12

SPCLK

(minimum) → f

sys

/(254×256)

Note:

The maximum baud-rate in the master mode is equal or less than 10Mbps.

TMPM3V6/M3V4

Page 325

2019-02-06

Summary of Contents for TMPM3V4
































































































































































































































































































































































































































































































































































Search results

Summary of Contents for TMPM3V4

Reviews:

Brands by name

Popular brands

Toshiba TMPM3V4, Manual

Search results

Summary of Contents for TMPM3V4

Reviews:

Brands by name

Popular brands