manualshive.com logo in svg

Toshiba TMPM3V4, Manual, Page: 268 / 544

Share
Download
Toshiba TMPM3V4 Manual Download Page 268

12.10.3  Transmit Operation

12.10.3.1  Operation of Transmit Buffer

If double buffering is disabled, the CPU writes data only to transmit shift register and the transmit inter-

rupt INTTXx is generated upon completion of data transmission.

If double buffering is enabled (including the case the transmit FIFO is enabled), data written to the trans-

mit buffer is moved to the transmit shift register. The INTTXx interrupt is generated at the same time

and the transmit buffer empty flag (SCxMOD2<TBEMP>) is set to "1". This flag indicates that the next

transmit data can be written. When the next data is written to the transmit buffer, the <TBEMP> flag is

cleared to "0".

DATA 1

Transmit buffer

SCxMOD2<TBEMP>

Transmit shift register(INTTXx)

Write data

DATA 2

DATA 1

   Transmit shift register

SCxMOD1<TXE>

Figure 12-8 Operation of Transmit Buffer (Double-buffer is enabled)

TMPM3V6/M3V4

12. Serial Channel with 4bytes FIFO (SIO/UART)
12.10 Transmit

Page 246

2019-02-06

Summary of Contents for TMPM3V4

































































































































































































































































































































































































































































































































































Reviews:

No comments