manualshive.com logo in svg

Toshiba TMPM3V4, Manual

Share
Download
Toshiba TMPM3V4 Manual Download Page 254

12.5.2  Parity Control

The parity bit can be added with a transmitted data only in the 7- or 8-bit UART mode. And the received par-

ity bit can be compared with a generated one.

Setting "1" to SCxCR<PE> enables the parity. SCxCR<EVEN> selects either even or odd parity.

12.5.2.1  Transmission

Upon data transmission, the parity control circuit automatically generates the parity with the data in the

 

transmit buffer. The parity bit will be stored in SCxBUF<TB

[

7

]

> in the 7-bit UART mode and

 

SCxMOD

0

<TB8> in the 8-bit UART mode.

The <PE> and <EVEN> settings must be completed before data is written to the transmit buffer.

12.5.2.2  Reception

If the received data is moved from the receive shift register to the receive buffer, a parity is generated.

In the 7-bit UART mode, the generated parity is compared with the parity stored in SCxBUF<RB

[

7

]

>,

 

in the 8-bit UART mode, it is compared with the one in SCxCR<RB8>.

If there is any difference, a parity error occurs and the SCxCR<PERR> is set to "1".

In use of the FIFO, <PERR> indicates that a parity error was generated in one of the received data.

12.5.3  STOP Bit Length

The length of the STOP bit in the UART transmission mode can be selected from one bit or two bits by set-

ting the SCxMOD2<SBLEN>. The length of the STOP bit data is determined as one-bit when it is received re-

gardless of the setting of this bit.

TMPM3V6/M3V4

12. Serial Channel with 4bytes FIFO (SIO/UART)
12.5 Data Format

Page 232

2019-02-06

Summary of Contents for TMPM3V4

































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands