Toshiba TMPM3V4 Manual Download Page 121

Page: 121 / 544

7.6.2.5 Interrupt Control Registers

Each interrupt source has the interrupt set-enable register, interrupt clear-enable register, interrupt

set-pending register and interrupt clear-pending register.

Each bit corresponds to each interrupt source.

(1)

Interrupt Set-Enable Register

This register enables interrupts and identifies whether the interrupt is enabled/disabled.

When set this register to "1", the corresponding interrupt is enabled.

Writing "0" has no meaning.

When this register is read, whether the corresponding interrupt is enabled or disabled is identified.

To clear the bit of this register, set "1" to the corresponding bit of the interrupt clear-enable register.

Bit symbol

Type

Function

SETENA

R/W

Interrupt No. [77:0]
[Write]
1: Enables interrupts.
[Read]
0: Interrupts are disabled.
1: Interrupts are enabled.

Note:

For descriptions of interrupts and interrupt numbers, see Section "7.5.1.5 List of Inter-

rupt Sources".

TMPM3V6/M3V4

Page 99

2019-02-06

Summary of Contents for TMPM3V4
































































































































































































































































































































































































































































































































































Search results

Summary of Contents for TMPM3V4

Reviews:

Brands by name

Popular brands

Toshiba TMPM3V4, Manual

Search results

Summary of Contents for TMPM3V4

Reviews:

Brands by name

Popular brands