Toshiba TMPM3V4 Manual Download Page 309

Page: 309 / 544

13.6 Data Transfer Procedure in the I2C Bus Mode

13.6.1 Device Initialization

Firstly, set SBICR1<ACK><SCK[2:0]>. Set "1" to <ACK> to specify the acknowledgement mode. Set

"000" to SBICR1<BC[2:0]> .

Secondly, set <SA[6:0]> (a slave address) and <ALS> to SBII2CAR . (In the addressing format mode, set

<ALS>="0").

Finally, to configure the Serial Bus Interface as a slave receiver, ensure that the serial bus interface pin is

at "High" first. Then write "000" to SBICR2<MST><TRX><BB>, "1" to <PIN>, "10" to <SBIM[1:0]> and

"00" to <SWRST[1:0]>.

Note:

Initialization of the serial bus interface circuit must be completed within a period that any device

does not generate start condition after all devices connected to the bus were initialized. If this rule is

not followed, data may not be received correctly because other devices may start transfer before the

initialization of the serial bus interface circuit is completed.

SBICR1

←

Specifies ACK and SCL clock.

SBII2CAR

←

Specifies a slave address and an address recognition mode.

SBICR2

←

Configures the SBI as a slave receiver.

Note:

X; Don’t care

13.6.2 Generating the Start Condition and a Slave Address

13.6.2.1 Master mode

In the master mode, the following steps are required to generate the start condition and a slave address.

First, ensure that the bus is free (<BB> = "0"). Then, write "1" to SBICR1<ACK> to select the acknowl-

edgment mode. Write to SBIDBR a slave address and a direction bit to be transmitted.

When <BB> = "0", writing "1111" to SBICR2<MST, TRX, BB, PIN> generates the start condition on

the bus. Following the start condition, the SBI generates nine clocks from the SCL pin. The SBI outputs

the slave address and the direction bit specified at SBIDBR with the first eight clocks, and releases the

SDA line in the ninth clock to receive an acknowledgment signal from the slave device.

The INTSBI interrupt request is generated on the falling of the ninth clock, and <PIN> is cleared to

"0". In the master mode, the SBI holds the SCL line at the "Low" level while <PIN> is = "0".<TRX>

changes its value according to the transmitted direction bit at generation of the INTSBI interrupt request, pro-

vided that an acknowledgment signal has been returned from the slave device.

Note:

To output salve address, check with software that the bus is free before writing to SBIDBR. If this

rule is not followed, data being output on the bus may get ruined.

TMPM3V6/M3V4

Page 287

2019-02-06

Summary of Contents for TMPM3V4
































































































































































































































































































































































































































































































































































Search results

Summary of Contents for TMPM3V4

Reviews:

Brands by name

Popular brands

Toshiba TMPM3V4, Manual

Search results

Summary of Contents for TMPM3V4

Reviews:

Brands by name

Popular brands