Toshiba TMPM3V4 Manual Download Page 346

Page: 346 / 544

d. Overrun interrupt

When the next data (9th data item) is received when the receive FIFO is already full, an overrun

interrupt is generated immediately after transfer. The data received after the overrun interrupt is gen-

erated (including the 9th data item) will become invalid and be discarded. However, if data is read

from the receive FIFO while the 9th data item is being received (before the interrupt is generated),

the 9th received data will be written in the receive FIFO as valid data. To perform transfer proper-

ly when the overrun interrupt has been generated, write "1" to SSPICR<RORIC> register, and then

read all data from the receive FIFO. Even if all the data is not read, data can be transmitted / re-

ceived if the receive FIFO has free space and the number of data to be transmitted does not exceed

the free space of the receive FIFO. Note that if the receive FIFO is not read (provided that the re-

ceive FIFO is not empty) within a certain 32-bit period (bit rate) after the overrun interrupt is

cleared, a time-out interrupt will be generated.

TMPM3V6/M3V4

14. Synchronous Serial Port (SSP)
14.4 Overview of SSP

Page 324

2019-02-06

Summary of Contents for TMPM3V4
































































































































































































































































































































































































































































































































































Search results

Summary of Contents for TMPM3V4

Reviews:

Brands by name

Popular brands

Toshiba TMPM3V4, Manual

Search results

Summary of Contents for TMPM3V4

Reviews:

Brands by name

Popular brands