manualshive.com logo in svg

Toshiba TMPM3V4, Manual

Share
Download
Toshiba TMPM3V4 Manual Download Page 317

"1" is confirmed by following the restart procedure. To check the status of the SCL line, read the
port.

7

6

5

4

3

2

1

0

SBICR2

←

0

0

0

1

1

0

0

0

Releases the bus.

if SBISR<BB> ≠ 0

Checks that the SCL pin is released.

Then

if SBISR<LRB> ≠ 1

Checks that no other device is pulling the SCL pin to the "Low".

Then

4.7 μs Wait

SBICR1

←

X

X

X

1

0

X

X

X

Selects the acknowledgment mode.

SBIDBR

←

X

X

X

X

X

X

X

X

Sets the desired slave address and direction.

SBICR2

←

1

1

1

1

1

0

0

0

Generates the start condition.

Note:

 

X; Don’t care

SCL pin

SCL(Bus)

"0"→<MST>

"0"→<TRX>

"0"→<BB>

"1"→<PIN>

SDA pin

<LRB>

<BB>

Start condition

<PIN>

"1"→<MST>

"1"→<TRX>

"1"→<BB>

"1"→<PIN>

4.7 ms (min.)

9

Figure 13-14 Timing Chart of Generating a Restart

TMPM3V6/M3V4

Page 295

2019-02-06

Summary of Contents for TMPM3V4

































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands