MX-3114N ADJUSTMENTS AND SETTINGS 5 – 84
2)
Select an adjustment target item with the scroll key.
Item/Display
Content
Setting
range
Default
value
Purpose (Case where the
adjustment is required)
Change when the adjustment value is
increased or decreased
Change
when the
adjustment
value is
changed by 1
A
FRONT
ADJUST
Alignment position
adjustment
(F side alignment
plate stop position)
(Paper alignment
adjustment)
2 - 18
10
This adjustment is used to
adjust the paper alignment
width when the paper
alignment is improper.
Alignment is determined by
the combination of the both
adjustment values of FRONT
ADJUST and REAR ADJUST.
F side paper
alignment
stop position
(F/R
direction)
When the adjustment value is
increased, the alignment plate stop
position is shifted to the R side.
When the adjustment value is
decreased, the alignment plate stop
position is shifted to the F side.
0.3665mm
B
REAR
ADJUST
Alignment position
adjustment
(R side alignment
plate stop position)
(Paper alignment
adjustment)
2 - 18
10
When changing the
adjustment values of FRONT
ADJUST and REAR ADJUST
from the default values, be
sure to change them by the
same variation.
R side paper
alignment
stop position
(F/R
direction)
When the adjustment value is
increased, the alignment plate stop
position is shifted to the F side.
When the adjustment value is
decreased, the alignment plate stop
position is shifted to the R side.
0.3665mm
C
STAPLE
REAR
Stapling position
adjustment (one
position at the
rear)
68 - 132
100
When the staple position on
the R side is shifted, perform
the adjustment.
Staple
position
(Stapler stop
position)
(F/R
direction)
When the adjustment value is
increased, the staple position is
shifted to the rear side.
When the adjustment value is
decreased, the staple position is
shifted to the front side.
0.155mm
D
STAPLE
FRONT
Stapling position
adjustment (one
position in front)
68 - 132
100
When the staple position on
the F side is shifted, perform
the adjustment.
Staple
position
(Stapler stop
position)
(F/R
direction)
When the adjustment value is
increased, the staple position is
shifted to the rear side.
When the adjustment value is
decreased, the staple position is
shifted to the front side.
0.155mm
E
STAPLE
BOTH
Stapling position
adjustment (center
position of two
positions binding)
68 - 132
100
When the staple off-center is
shifted, perform the
adjustment.
Staple
position
(Stapler stop
position)
(F/R
direction)
When the adjustment value is
increased, the staple position is
shifted to the rear side.
When the adjustment value is
decreased, the staple position is
shifted to the front side.
0.155mm
F
STAPLE
PITCH
Stapling position
adjustment (staple
pitch of two
positions binding)
68 - 132
100
When it is required to change
the staple interval, perform
the adjustment.
Staple
position
(Stapler stop
position)
(F/R
direction)
When the adjustment value is
increased, the staple interval is
increased.
When the adjustment value is
decreased, the staple interval is
decreased.
0.155mm
G
PUNCH
CENTER
Punch center
positioning sensor
37 - 63
50
When the punch off-center is
shifted, perform the
adjustment.
Punch
position
(F/R
direction)
When the adjustment value is
decreased, the punch position is
shifted to the front side.
When the adjustment value is
increased, the punch position is
shifted to the rear side.
0.1441mm
H
PUNCH
HOLE
Punch hole
adjustment (paper
transport direction)
42 - 58
50
When the punch hole position
is shifted in the transport
direction, perform the
adjustment.
Punch
position
(Paper
transport
direction)
When the adjustment value is
increased, the punch position is
shifted to the paper lead edge side.
When the adjustment value is
decreased, the punch position is
shifted to the paper rear edge side.
0.2584mm
