MX-3114N SIMULATION 6 – 7
62
8
Used to format the hard disk/SD Card. (HDD: Excluding the Operation Manual, the watermark data, and
the system area) (SD Card: User data)
10
Used to clear the job completion list data.
11
Used to delete the document filing data.
12
Used to set Enable/Disable of auto format in a hard disk trouble.
13
Used to format the hard disk. (Operation Manual, watermark data only)
14
Used to delete the document filing management data.
HDD
63
1
Used to display the shading correction result.
Scanner
2
Used to perform shading.
3
Used to perform scanner (CCD) color balance and gamma auto adjustment.
Scanner
4
Used to display the SIT chart patch density.
5
Used to perform the scanner (CCD) color balance and gamma default setting.
6
Used to display the scan level and the density level of the copy color balance adjustment patch.
7
Used to register the service target of the copy mode auto color balance adjustment.
8
Used to set the default of the service target of the copy mode auto color balance adjustment.
11
Used to set the target color balance of the copy mode auto color balance adjustment.
64
1
Test print. (Self print) (Color mode)
2
Test print. (Self print) (Monochrome mode)
4
Printer test print. (Self print)
5
Printer test print. (Self print) (PCL)
6
Printer test print. (Self print) (PS)
7
Used to print the adjustment pattern of the test print .(Self print).
(The adjustment pattern of SIM46-21 is printed.)
65
1
Used to adjust the touch panel (LCD display section) detection coordinates.
Operation panel section
2
Used to display the touch panel (LCD display section) detection coordinates.
5
Used to check the operation panel key input.
66
1
Used to display the FAX-related soft SW (2 - 150) on the LCD to allow changing the soft SW while
checking with the LCD.
FAX
2
Used to enter a country code and set the default value for the country code.
FAX
3
Used to check read/write of the EEPROM and the SDRAM on the MODEM controller and display the
result.
FAX
4
Used to send the selected signals to the line and the main unit speaker. (Send level: max.)
FAX
5
Used to send the selected signal to the line and the main unit speaker. (Send level: Soft SW setting)
(For the kinds of send signals, refer to SIM66-04.)
FAX
6
Used to print the confidential registration check table (BOX NO., BOX name, passcode. (If there is no
confidential registration, no print is made.)
FAX
7
Used to output all image data saved in the image memory. (Confidential data are also outputted.)
FAX
8
Used to send the selected sound messages to the line and the speaker. (Send level: Max.)
FAX
9
Used to send the selected sound message to the line and the speaker. (Send level: Soft SW setting)
* For details of sound messages, refer to the sound message table of SIM66-08.
FAX
10
Used to clear the FAX and image send image data. (The confidential data are also cleared.)
FAX
11
Used to send the selected signal at 300bps to the line and the speaker. (Send level: Max.)
FAX
12
Used to send the selected signal at 300bps to the line and the speaker. (Send level: Soft SW setting)
* For the kings of send signals at 300bps, refer to SIM66-11, 300bps send signal table.
FAX
13
Used to register dial numbers for SIM66-14/15/16, Dial test. (Up to 20 digits can be registered.)
FAX
14
Used to execute the dial pulse (10PPS) send test and to adjust the make time.
FAX
15
Used to execute the dial pulse (20PPS) send test and to adjust the make time.
FAX
16
Used to execute the DTFM signal send test and to adjust the send level.
FAX
17
Used to send the DTMF signal to the line and the speaker. (Send level: Max.)
FAX
18
Used to send the DTMF signal to the line and the speaker. (Send level: Soft SW setting)
FAX
21
Used to print the selected items (system error, protocol monitor).
FAX
22
Used to set the handset sound volume. (This simulation can be executed even though the handset setting
is set to NO. When, however, the handset is not installed, the sound volume cannot be checked.) (Japan
model only)
FAX
24
Used to clear the FAST save data.
FAX
29
Used to initialize the telephone book data (the one-touch registration table, the FTP/Desktop expansion
table, the group expansion table, the program registration table, the interface memory box table, the meta
data, InboundRouting, and the DocumentAdmin table).
FAX
30
Used to display the TEL/LIU status change, The display is highlighted by status change.
FAX
31
Used to set ON/OFF the port for output to TEL/LIU.
FAX
32
Used to check the fixed data received from the line and to display the result.
FAX
33
Used to execute detection of various signals with the line connected and to display the detection result.
When a signal is detected, the display is highlighted.
FAX
34
Used to execute the send test and display the time required for sending image data in the test. Used to
execute send test and display. (Unit: ms)
FAX
36
Used to check send and receive data from the MODEM controller to the MFP controller or the data line or
the command line individually.
FAX
39
Used to check and change the destination setting saved in EEPROM of the FAX BOX.
FAX
42
Used to rewrite the program to power control installed in the FAX BOX.
FAX
43
Used to write the adjustment value into the power control installed in the FAX BOX.
FAX
61
Used to display the FAX-related soft SW (151 - 250) on the LCD to allow changing the soft SW while
checking with the LCD.
FAX
62
Used to import the FAX receive data into a USB memory in PDF file type.
FAX
Main
Sub
Functions
Section
