manualshive.com logo in svg

Sharp AR-M550N, Service Manual, Page: 177 / 460

Share
Download
Sharp AR-M550N Service Manual Download Page 177

: Feb. 6 2004

1

AR-M550/M620/M700  DETAILS OF EACH SECTION  6 - 122

4) Remove the E-ring, and remove the SPF paper feed clutch.

5) Disconnect the connector, and remove the SPF document tray

upper limit detector (A), the SPF document upper limit detector (B),
the SPF cover switch (C), and the SPF document paper pass
detector 1 (D).

b-1. Separation roller

1) Remove the paper feed roller and the pickup roller. (“a-1. Paper

feed roller” and “a-2. Pickup roller” in this section.)

2) Remove the cover.

3) Unhook the claw to remove the support. Remove the reverse

roller.

[Caution when attaching] 

• Rotate the roller into the pin slot.

b-2. SPF paper feed/paper transport motor

1) Remove the rear cover. (See “a-1. Cabinet” in the previous sec-

tion, “[External outfit section]”) 

2) Remove the SPF paper feed/paper transport motor.

b-3. SPF resist roller brake clutch

b-4. SPF resist roller clutch

1) Remove the rear cover. (See “a-1. Cabinet” in the previous sec-

tion, “[External outfit section]”) 

b-5. No. 1 resist roller (Drive)

b-6. Torque limiter

1) Remove the cabinet. (See “a-1. Cabinet” in the previous section,

“[External outfit section]”)

2) Remove the document feed tray unit. (See “a. Paper feed unit” in

this section)

3) Remove the plastic E-ring in the arrow direction and remove the

No. 1 resist roller idle.

C

D

B

A

2) Disconnect the connector, and remove the clamp, the plastic E-

ring, the SPF resist roller brake clutch (A), and the SPF resist roller
clutch (B).

1

A

B

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Reviews:

No comments