Sharp AR-M550N Service Manual Download Page 240

Page: 240 / 460

: Feb. 9 2004

AR-M550/M620/M700 SETTING AND ADJUSTMENTS 7 - 25

(Scan off-center adjustment)

1) Place a duplex document in the SPF original tray.

2) Press the Start key

Since the front side and back side images are copied onto sepa-
rate sheets, check the off-center of the back side image.

If the above requirement is not met, do the following steps.

3) Using the numeric keypad, change the adjustment value in steps

of 0.1 mm to adjust the scan image off-center. A larger setting
shifts the printed image toward the front side.

4) Press the P or Start key.

Pressing the Start key starts copy operation as well as applying the
adjustment value.

5) Check the off-center of the printed image.

Repeat the above adjustments until an acceptable result is obtained.

This adjustment is needed in the following situations:

• The paper feed section has been disassembled.

• The MFP control PWB has been replaced.

• The EEPROM on the MFP control PWB has been replaced.

• The scan control PWB has been replaced.

• The EEPROM on the scan control PWB has been replaced.

• The scanner (reading) section has been disassembled.

• The scanner (reading) unit has been replaced.

• The LSU has been replaced.

• U2 trouble has occurred.

1) Go through the modes specified in Simulation 50-1.

If the off-center is 0±2.7 mm, no adjustment is required.

ADJ 8

Adjusting the image position,
image loss, and void area

ADJ 8A

Adjust copied image loss/void area in
original table mode

original

copy

Select 2, and
press [START] key.

Press [START] key, or
press [CUSTOM SETTINGS] key.

Image loss (LIL)

LIL = 1.5 mm
LV

= 3.5 mm

TV = 3.5 mm

FV+RV = 7.0 mm

Papar lead edge

Papar tail edge

No Image

Void (TV)

Void (LV)

Void (FV)

Void (RV)

Press [CUSTOM SETTINGS] key.

Press [START] key.

Press [CUSTOM SETTINGS] key,
or terminate copying.

Press [START] key or
press [CUSTOM SETTINGS] key.

SIMULATION 50-1

LEAD EDGE ADJUSTMENT. INPUT VALUE 0-99, AND PRESS

START.

3.RRCA

SIMULATION 50-1

LEAD EDGE ADJUSTMENT. NOW COPYING.

SIMULATION 50-1

LEAD EDGE ADJUSTMENT. SELECT 1-6, AND PRESS START.

(FEED TRAY)

1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4

5.BPT 6.LCC

Select 1, and
press [START] key.

Select 0, and press [START] key.

Select other than 0 - 2, and press [START] key.

SIMULATION 50-1

LEAD EDGE ADJUSTMENT. SELECT 0-9, AND PRESS START.

0.TRAY SELECT

1.COPY START

2.MAGNIFICATION

100

(ADJUSTMENT DATA) 3.RRCA

4.RRCB

10.SIDE2 ADJ.

(IMAGE LOSS SETTING) 5.LEAD

6.SIDE

(VOID SETTING) 7.LEAD_EDGE(DENA)

8.TRAIL_EDGE(DENB)

9.FRONT/REAR

100

SIMULATION 50-1

LEAD EDGE ADJUSTMENT.

(MAGNIFICATION)

INPUT 25-400(%)

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Search results

Summary of Contents for AR-M550N

Reviews:

Sharp AR-M550N, Service Manual, Page: 240 / 460

Search results

Summary of Contents for AR-M550N

Reviews: