manualshive.com logo in svg

Sharp AR-M550N, Service Manual, Page: 268 / 460

Share
Download
Sharp AR-M550N Service Manual Download Page 268

: Feb. 9 2004

1

AR-M550/M620/M700  SIMULATION  8 - 10

22

1

Used to check the print count value 
in each section and each operation 
mode. (Used to check the 
maintenance timing.)

Adjustment/Setup/
Operation data output/
Check (Display/Print)

Counter

2

Used to check the total numbers of 
misfeed and troubles. (When the 
number of misfeed is considerably 
great, it is judged as necessary for 
repair. The misfeed rate is obtained 
by dividing this count value with the 
total counter value.)

Adjustment/Setup/
Operation data output/
Check (Display/Print)

Trouble

3

Used to check misfeed positions and 
the misfeed count of each position. 
(If the misfeed count is considerably 
great, it may be judged as necessary 
to repair.)

Adjustment/Setup/
Operation data output/
Check (Display/Print)

Sections other 
than SPF/DSPF 
section

Trouble

Misfeed

4

Used to check the trouble (self diag) 
history.

Adjustment/Setup/
Operation data output/
Check (Display/Print)

Trouble

5

Used to check the ROM version of 
each unit (section).

Other

Software

6

Used to output the list of the setting 
and adjustment data (simulations, 
FAX soft switch, counters).

Adjustment/Setup/
Operation data output/
Check (Display/Print)

Data

Adjust/Setting 
data

7

Used to display the key operator 
code. (This simulation is used when 
the customer forgets the key 
operator code.)

Adjustment/Setup/
Operation data output/
Check (Display/Print)

Data

User data

8

Used to check the number of use of 
the finisher, the SPF, and the scan 
(reading) unit.

Adjustment/Setup/
Operation data output/
Check (Display/Print)

Optical (Image 
scanning)

Finisher

Counter

9

Used to check the number of use 
(print quantity) of each paper feed 
section.

Adjustment/Setup/
Operation data output/
Check (Display/Print)

Paper feed, ADU

Counter

10

Used to check the system 
configuration (option, internal 
hardware). 

Adjustment/Setup/
Operation data output/
Check (Display/Print)

Specifications

Options

11

Used to check the use frequency 
(send/receive) of FAX. (Only when 
FAX is installed)

Adjustment/Setup/
Operation data output/
Check (Display/Print)

FAX

Data

12

Used to check the SPF misfeed 
positions and the number of misfeed 
at each position. (When the number 
of misfeed is considerably great, it 
can be judged as necessary for 
repair.)

Adjustment/Setup/
Operation data output/
Check (Display/Print)

DSPF

Trouble

13

Used to check the operating time of 
the process section (OPC drum, DV 
unit, toner bottle).

Adjustment/Setup/
Operation data output/
Check (Display/Print)

Counter

19

Used to check the values of the 
counters related to the scan mode 
and the internet FAX mode.

Adjustment/Setup/
Operation data output/
Check (Display/Print)

Scanner

Counter

23

2

Used to check the trouble history of 
paper jam and misfeed. (If the 
number of misfeed and troubles is 
considerably great, it may be judged 
as necessary to repair.)

Adjustment/Setup/
Operation data output/
Check (Display/Print)

Trouble

80

Used to check the operations of the 
sensors and detectors in the paper 
feed and transport section.

Operation test/Check

Paper feed, paper 
transport

Operation

Code

Function (Purpose)

Purpose

Section

Item

Main

Sub

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Reviews:

No comments