manualshive.com logo in svg

Sharp AR-M550N, Service Manual, Page: 211 / 460

Share
Download
Sharp AR-M550N Service Manual Download Page 211

: Feb. 6 2004

1

AR-M550/M620/M700  DETAILS OF EACH SECTION  6 - 156

7) Remove the toner bottle. (See “a. Toner bottle unit”    in  “[Toner

hopper and toner bottle section]”)

8) Remove the toner hopper unit. (See “b. Toner hopper unit”  in

“[Toner hopper and toner bottle section]”)

9) Remove the developing unit. (See “a. Developing unit” in the

“[Developer tank section]”)

10) Remove the process unit. (See “a. Process unit” in the “[OPC drum

section]”)

11) Raise the process DV cover diagonally, and remove the front right

cover.

12) Remove the front cabinet upper.

13) Remove the paper exit tray cabinet unit.

14) Remove the paper exit port cabinet, and remove the paper exit tray

cabinet C.

15) Disconnect the connector and remove the harness clamp. Remove

the main duct unit.

16)  Remove the fan unit.

17) Disconnect the connector and remove the process exhaust fan

motor 1 (A), 2 (A), and 3 (C).

NOTE: When assembling, fit the mark with the fan rotating direction

(label on the back surface). 

1

1

A

B

C

Fan blowing direction

Marks

Mark

REVERSE

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Reviews:

No comments