manualshive.com logo in svg

Sharp AR-M550N, Service Manual, Page: 354 / 460

Share
Download
Sharp AR-M550N Service Manual Download Page 354

AR-M550/M620/M700  SIMULATION  8 - 96

Operation/Procedure

1) Select YES/NO of Modem program reload.

2) Press [START] key.

When reload is completed normally, "OK" is displayed. In case of an
error, "CHECK SUM" is displayed.

The result of Modem reload is displayed.

Operation/Procedure

1) Enter the number corresponding to the check mode with 10-key.

2) Press [START] key.

When check is completed normally, "OK" is displayed. Incase of an
error, "NG" is displayed.

When check is "repeat," the operation is continued until the result is
NG or [CUSTOM SETTINGS] key is pressed.

Operation/Procedure

1) Enter the number corresponding to the destination.

2) Press [START] key.

Operation/Procedure

1) Enter the number corresponding to the set item with 10-key.

The item list menu can be switched by pressing [P] key.

2) Press [START] key.

3) Enter the set value.

4) Press [START] key.

This simulation can be executed when soft SW 24-4 and 24-5 are set
to 1. Display/Not display is switched by soft SW 24-4 and 24-5. 

The digit limitation and characters allowed to be inputted depend on
the input item.

66-35

Purpose

Setting

Function
(Purpose)

Modem program reloading (Only when FAX is 
installed)
Not used in the market. (For development)

Section

FAX

Item

Data

1

YES

Modem block reload is cleared.

2

NO

Not reloaded.

COMPLETE

Reload completed

81

Check sum error

82

Write error

83

Delete error

84

Verify error

NG

Due to loader NG

Press [START] key.

After completion of reloading

66-36

Purpose

Operation test/Check

Function
(Purpose)

Used to check interface between MFPC controller and 
MDMC. (Check of the data line or the command line)

Section

FAX

Item

Operation

1

MFPC 

←

 MDMC

Date line once only

2

MFPC 

→

 MDMC

Date line once only

3

MFPC 

←

 MDMC

Data line repeat

4

MFPC 

→

 MDMC

Data line repeat

5

MFPC 

←

 MDMC

Command line once only

6

MFPC 

→

 MDMC

Command line once only

7

MFPC 

←

 MDMC

Command line repeat

8

MFPC 

→

 MDMC

Command line repeat

SIMULATION 66-35

MODEM PROGRAM RELOAD.

ARE YOU SURE?

1. YES

2. NO

1

SIMULATION 66-35

MODEM PROGRAM RELOAD.

EXECITOMG···

LOADER··· xxxxx

MODEM···· xxxxx

SIMULATION 66-35

MODEM PROGRAM RELOAD.

LOADER···OK

MODEM····COMPLETE

66-39

Purpose

Setting

Function
(Purpose)

Used to set the destination specifications.

Section

FAX

Item

Specifications Operation

66-60

Purpose

Setting

Function
(Purpose)

Used to set the ACR data.

Section

FAX

Item

Operation

SIMULATION 66-36

MFPC-MDMC I/F CHECK. INPUT 1-8, AND PRESS START.

1. MFPC<-MDMC(DATA once)

2. MFPC->MDMC(DATA once)

3. MFPC<-MDMC(DATA repeat)

4. MFPC->MDMC(DATA repeat)

5. MFPC<-MDMC(CMD once)

6. MFPC->MDMC(CMD once)

7. MDPC<-MDMC(CMD repeat)

8. MFPC->MDMC(CMD repeat)

1

SIMULATION 66-36

MFPC-MDMC I/F CHECK. INPUT 1-8, AND PRESS START.

EXECUTING...(OK or NG)

SIMULATION 66-36

MFPC-MDMC I/F CHECK. INPUT 1-8, AND PRESS START.

EXECUTING...

Press [START] key.

When check is "once" or 
"repeat" and the result is "NG": 

When check is "repeat" and 
[CUSTOM SETTINGS] key ON:

Press [START] key.

SIMULATION 66-39

  FAX DESTINATION SETUP.

  SELECT 1-6, AND PRESS START

0. NO DESTINATION

1. JAPAN

2. U.S.A./CANADA

3. EUROPE

4. AUSTRALIA

5. CHINA

6. ASIA

1

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Reviews:

No comments