manualshive.com logo in svg

Sharp AR-M550N, Service Manual, Page: 332 / 460

Share
Download
Sharp AR-M550N Service Manual Download Page 332

: Feb. 9 2004

1

AR-M550/M620/M700  SIMULATION  8 - 74

Operation/Procedure

(Select the scan mode to be adjusted.)

1) Enter the number corresponding to the paper feed tray to be

adjusted with 10-key.  (Select one of 2 - 12.)

2) Press [START] key.

(Resist adjustment)

1) Enter the resist adjustment value with 10-key.

2) Press [START] key. 

When [START] key is pressed, the adjustment value is set and
paper feed and copying are performed.

(Copy condition setting in this simulation)

∗

To select paper (paper feed tray), perform the following procedures.

1) Enter 0 with 10-key. 

2) Press [START] key. (The mode is changed to the paper feed tray

selection mode.)

3) Enter the number corresponding to the paper feed tray to be used

with 10-key. 

4) Press [START] key. (The paper feed tray is selected.)

When the total of the above set value (1 - 6) and 10 is entered, the
mode is changed to the duplex print mode.

NOTE: When [P] key is pressed after entering the adjustment value in

this simulation, the adjustment value is set. When [START] key
is pressed, the adjustment value is set and copying is per-
formed.

Scanner mode

10

OC (LEAD_EDGE)

OC lead edge

0 - 10

(Unit 1mm)

0 

(0mm)

11

OC (FRONT/REAR)

OC side

12

OC (TRAIL_EDGE)

OC rear edge

13

SPF (LEAD_EDGE)

SPF lead edge

14

SPF (FRONT/REAR) SPF side

15

SPF (TRAIL_EDGE)

SPF rear edge

16

CIS (LEAD_EDGE)

CIS lead edge

17

CIS (FRONT/REAR)

CIS side

18

CIS (TRAIL_EDGE)

CIS rear edge

Press [START] key.

Press [CUSTOM SETTINGS] key.

51

51-2

Purpose

Adjustment

Function
(Purpose)

Used to adjust the contact pressure of paper on the 
resist roller of each section (each paper feed, duplex 
feed and SPF paper feed of the copier). (This 
adjustment is required when the print image position 
variations are considerably great or when paper jams 
occur frequently.)

Section

Paper transport (Discharge/Switchback/Transport)

Item

Operation

Item

Set 

range

Default

AR-M550N/U, 

AR-620N/U

AR-

M700N/U

0

TRAY SELECT Paper feed tray 

selection 
(1 - 5)

–

–

–

1

PRINT START Print start (Default)

–

–

–

2

TRAY1

Tray 1 adjustment value 0 - 99

46

48

3

TRAY2

Tray 2 adjustment value

45

46

4

TRAY3

Tray 3 adjustment value

46

47

5

TRAY4

Tray 4 adjustment value

6

BPT

Manual feed tray resist 
adjustment value

45

46

7

LCC

Side LCC resist 
adjustment value

8

ADU

ADU resist adjustment 
value

43

46

9

SPF (TOP)

SPF resist adjustment 
value (Top speed)

50

Item

Set range

Default

1

1

SIMULATION 50-27

ORIGINAL IMAGE LOSS SETTING(FAX/SCN). SELECT 1-18, AND

PRESS START.

[FAX]

1.OC(LEAD_EDGE)  

0 

2.OC(FRONT/REAR)  

0 

3.OC(TRAIL_EDGE)  

0

4.SPF(LEAD_EDGE) 

0 

5.SPF(FRONT/REAR) 

0 

6.SPF(TRAIL_EDGE) 

0

7.CIS(LEAD_EDGE) 

0 

8.CIS(FRONT/REAR) 

0

 9.CIS(TRAIL_EDGE) 

0

[SCN]

10.OC(LEAD_EDGE)  

0 

11.OC(FRONT/REAR)  

0

 12.OC(TRAIL_EDGE)  

0

13.SPF(LEAD_EDGE) 

0 

14.SPF(FRONT/REAR) 

0

 15.SPF(TRAIL_EDGE) 

0

16.CIS(LEAD_EDGE) 

0 

17.CIS(FRONT/REAR) 

0

 18.CIS(TRAIL_EDGE) 

0

0

SIMULATION 50-27

ORIGINAL IMAGE LOSS SETTING(FAX/SCN). INPUT 0-10, AND

PRESS START.

1.OC(LEAD_EDGE)

1

10 SPF (HIGH)

SPF resist adjustment 
value (High speed)

0 - 99

50

11 SPF (LOW)

SPF resist adjustment 
value (Low speed)

12 SPF FEED 

(TOP)

SPF paper fed resist 
adjustment value (Top 
speed)

0 - 99

50

13 SPF FEED 

(HIGH)

SPF paper feed resist 
adjustment value (High 
speed)

14 SPF FEED 

(LOW)

SPF paper feed resist 
adjustment (Low speed)

Normal display

NOW PRINTING.

ERROR display

Door open

DOOR OPEN.

Jam

JAM

Paper empty

PAPER EMPTY.

1

TRAY1

TRAY1

2

TRAY2

TRAY2

3

TRAY3

TRAY3

4

TRAY4

TRAY4

5

BPT

Manual feed

6

LCC

LCC

Item

Set 

range

Default

AR-M550N/U, 

AR-620N/U

AR-

M700N/U

1

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Reviews:

No comments