Home
/
Sharp
/
AR-M550N
/
Service Manual

Sharp AR-M550N, Service Manual, Page: 246 / 460

Share

Page: 246 / 460

Sharp AR-M550N Service Manual Download Page 246

: Feb. 9 2004

1

AR-M550/M620/M700 SETTING AND ADJUSTMENTS 7 - 31

3) Using the numeric keypad, select the number that corresponds to

the copy mode for which to make adjustments. (Choose from
numbers 3 to 6.)

4) Press the Start key

5) Press the Start key (A copy is created.)

Check the density of the copied image.

If the copied image density is not at an acceptable level, do the fol-
lowing steps.

6) Adjust the copy density by entering an appropriate value through

the numeric keypad.

A larger value provides higher density.

7) Press the P or Start key

This applies the adjustment value.

Pressing the Start key starts copy operation as well as applying the
adjustment value.

8) Check the copied image density.

Repeat steps 6 to 8 until an acceptable copied image density is
obtained.

Note: Adjusting the copied image density through this simulation

changes the copied image density settings for all copy modes to
the copied image density level applied by carrying out this simu-
lation. Also, the copied image density gradient is automatically
adjusted to the specified level.
The copied image density settings for individual copy modes
adjusted through Simulations 46-9, -10, and -11 are changed to
the copied image density level applied by this simulation.

This adjustment is intended to customize the copied image density set-
tings. The copy density setting for each copy density adjustment level
(1 to 5) in manual copy mode can be adjusted to a custom density
level.

1) Set the test chart (UKOG-0162FCZZ) on the original table.

2) Go through the simulation modes that correspond to the copy

modes for which to adjust the copy density (i.e., the modes speci-
fied in Simulations 46-9, -10, or -11).

(SIM 46-9) (Text mode)

3

AE 3.0

AE mode

0 - 99

50

4

CH 3.0

Text mode 3.0

5

MIX 3.0

Text/Photo mode 3.0

6

PHOTO 3.0

Photo mode 3.0

ADJ 9B

Adjust the copy density in text binary
mode

ADJ 9C

Adjust the copy density in text/photo
binary mode

ADJ 9D

Adjust the copy density in photo binary
mode

Item

Set

range

Default

Select 2, and press [START] key.

Press [START] key, or
press [CUSTOM SETTINGS] key.

Item

Set

range

Default

0

TRAY SELECT

Paper feed tray selection

1

COPY START

Copy START (Default)

2

EXP LEVEL

Exposure level selection

3

1.0

Exposure level 1.0

0 - 99

50

4

1.5

Exposure level 1.5

5

2.0

Exposure level 2.0

6

2.5

Exposure level 2.5

7

3.0

Exposure level 3.0

8

3.5

Exposure level 3.5

9

4.0

Exposure level 4.0

10

4.5

Exposure level 4.5

11

5.0

Exposure level 5.0

SIMULATION 46-9

Select other than 0 - 2, and
press [START] key.

Press
[CUSTOM SETTINGS] key.

SIMULATION 46-9

EXP. LEVEL SETUP (CHAR.2). INPUT VALUE 0-99, AND PRESS

START.

3. 1.0

Press [START] key.

SIMULATION 46-9

EXP. LEVEL SETUP (CHAR.2). NOW COPYING.

50

Press [CUSTOM SETTINGS] key,
or terminate copying.

SIMULATION 46-9

EXP. LEVEL SETUP (CHAR.2). SELECT 1-6, AND PRESS START.

(FEED TRAY)

1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4

5. BPT 6. LCC

Press [START] key, or
press [CUSTOM SETTINGS] key.

1

Select 0, and
press [START] key.

1

Select 1,
and press
[START] key.

EXP. LEVEL SETUP (CHAR.2). SELECT 0-11, AND PRESS START.

0. TRAY SELECT

1

1. COPY START

2. EXP LEVEL

1

3. 1.0

50

4. 1.5

50

5. 2.0

50

6. 2.5

50

7. 3.0

50

8. 3.5

50

9. 4.0

50

10. 4.5

50

11. 5.0

50

SIMULATION 46-9

EXP. LEVEL SETUP (CHAR.2). SELECT 3-11, AND PRESS START.

(EXP. LEVEL SELECT)

3. 1.0 4. 1.5 5. 2.0

6. 2.5 7. 3.0 8. 3.5

9. 4.0 10. 4.5 11. 5.0

1

«
...
244
245
246
247
248
...
»

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Reviews:

No comments