manualshive.com logo in svg

Sharp AR-M550N, Service Manual, Page: 326 / 460

Share
Download
Sharp AR-M550N Service Manual Download Page 326

: Feb. 9 2004

1

AR-M550/M620/M700  SIMULATION  8 - 68

Operation/Procedure

(Print image off-center position adjustment)

1) Enter the number corresponding to the paper feed tray to be

adjusted with 10-key. (Select one of 10 - 16.) (Table 1)

2) Press [START] key.

3) Enter the adjustment value with 10-key.

4) Press [P] key or [START] key. When [START] key is pressed, the

adjustment value is set and printing is performed. (Table 2)

Check the off-center of the self-print patter of print-out.

(Shift for the adjustment value change: 0.1mm/step)

The greater the adjustment value is, the more the print image is shifted
to the front.

(Lead edge void area adjustment)

1) Set the lead edge void adjustment value (DENA) as specified

below.

(Standard set value) Paper lead edge void: 3.5mm (DENA: 35)

∗

Set the adjustment value of DENA to 35. Enter 35 as the adjust-
ment value of DENA, and press [P] key.

2) Check the lead edge void area on the self print pattern.

(Enter 1 and press [START] key.)

3) If the adjustment result is not satisfactory, perform the following

procedures.

∗

If the lead edge void area is not 3.5mm:
Change the adjustment value of RRCB and perform the adjust-
ment. (Change the adjustment value of RRCB and press
[START] key.)
(Shift for the adjustment value change: 0.1mm/step)

(Front/rear frame direction void area adjustment)

Adjust so that the total of the front/rear direction void areas is 7.0mm.
(Change the adjustment values of FRONT/REAR, and press [START]
key.)

Front frame void area = 3.5mm

Rear frame void area = 3.5mm

(Paper resist adjustment)

1) Enter the number corresponding to the paper feed tray to be

adjusted with 10-key. (Select one of 3 - 9.) (Table 1)

2) Press [START] key.

3) Enter the adjustment value with 10-key.

4) Press [P] key or [START] key. When [START] key is pressed, the

adjustment value is set and printing is performed. (Table 2)

If the relative positions of paper and print images vary or a paper jam
occurs, change the adjustment value.

(Print condition setting in this simulation)

∗

To select paper (paper feed tray), perform the following procedures.

1) Enter 0 with 10-key. 

2) Press [START] key. (The mode is changed to the paper feed tray

selection mode.)

3) Enter the number corresponding to the paper feed tray to be used

with 10-key. (Table 3)

4) Press [START] key. (The paper feed tray is selected.)

When the total of the above set value (1 - 6) and 10 is entered, the
mode is changed to the duplex print mode. 

NOTE: When [P] key is pressed after entering the adjustment value in

this simulation, the adjustment value is set. When [START] key
is pressed instead, the adjustment value is set and copying is
performed.

(Table 1)

Select 2, and 
press [START] key.

Press [START] key, or 
press [CUSTOM SETTINGS] key.

50-5

Purpose

Adjustment

Function
(Purpose)

Used to adjust the print image position and the void 
area (image loss) on print paper. (Adjustment as the 
print engine) (This adjustment is reflected on all the 
FAX/printer/copy modes.)

Section

Item

Picture quality

320

1

2

SIMULATION 50-2
LEAD EDGE ADJUSTMENT(CALC). SELECT 0-9, AND PRESS 
START.
0. TRAY SELECT 

1  

1.COPY START

2. MAGNIFICATION 

400

(ADJUSTMENT) 3.LT 

320

 4.L2 

105

(IMAEG LOSS SETTING) 5.LEAD 

15

 6.SIDE 

20

(VOID SETTING) 7.LEAD_EDGE(DENA) 

50

              8.TRAIL_EDGE(DENB) 

30

 9.FRONT/REAR 

30

Select other than 0 - 2, and press [START] key.

Press [CUSTOM SETTING] key.

Press [START] key. 

Press [CUSTOM SETTING] key, 
or terminate copying.

Press [CUSTOM SETTING] key, 
or terminate copying.

SIMULATION 50-2

LEAD EDGE ADJUSTMENT(CALC). INPUT VALUE 0-99, AND PRESS

START.

3.L1

SIMULATION 50-2

LEAD EDGE ADJUSTMENT(CALC). NOW COPYING.

SIMULATION 50-2

LEAD EDGE ADJUSTMENT(CALC). SELECT 1-6, AND PRESS

START.

(FEED TRAY)

   1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4

   5.BPT   6.LCC

Select 1, 
and press 
[START] key.

Select 0, and press [START] key.

100

SIMULATION 50-2

LEAD EDGE ADJUSTMENT(CALC).

(MAGNIFICATION)

  INPUT 25-400(%)

Item

Set 

range

Default

AR-M550N/U, 

AR-620N/U

AR-

M700N/U

0

TRAY SELECT

Paper feed tray 
selection (1 - 6)

–

–

1

PRINT START

Print start (Default)

–

–

(Lead edge adjustment value)

2

RRCB

Resist roller clutch ON 
timing adjustment value

0 - 99

50

(Resist adjustment value)

3

TRAY1

Tray 1 adjustment

0 - 99

46

48

4

TRAY2

Tray 2 adjustment

45

46

5

TRAY3

Tray 3 adjustment

46

47

6

TRAY4

Tray 4 adjustment

46

47

7

BPT

Manual feed tray 
adjustment

45

46

8

LCC

Side LCC adjustment

45

46

9

ADU

Adjustment when paper 
is fed again from ADU

43

46

(Off-center set value) Self print

10

TRAY 1

Tray 1 adjustment

0 - 99

50

11

TRAY 2 

Tray 2 adjustment

12

TRAY 3

Tray 3 adjustment

13

TRAY 4

Tray 4 adjustment

14

BPT

Manual feed tray 
adjustment

15

LCC

Side LCC adjustment

16

ADU

Adjustment when paper 
is fed again from ADU

1

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Reviews:

No comments