manualshive.com logo in svg

Sharp AR-M550N, Service Manual, Page: 237 / 460

Share
Download
Sharp AR-M550N Service Manual Download Page 237

: Feb. 9 2004

1

AR-M550/M620/M700  SETTING AND ADJUSTMENTS  7 - 22

2) Enter the number that corresponds to the paper feed tray that

needs adjustments.  (Choose from numbers 10 to 16.)

3) Press the Start key

4) Press the Start key

A self-print pattern image is printed. 

Check the off-center of the printed self-print pattern image. 

If so, no adjustment is required.

If the above requirement is not met, do the following steps. 

5) Using the numeric keypad, change the adjustment value in steps

of 0.1 mm. A larger setting shifts the printed image toward the front
side.  

6) Press the P or Start key.  Pressing the Start key starts print opera-

tion as well as applying the adjustment value. 

Check the off-center of the printed self-print pattern image. 

Repeat steps 5 to 6 until an acceptable result is obtained. 

This adjustment is needed in the following situations: 

• The MFP control PWB has been replaced.

• The EEPROM on the MFP control PWB has been replaced.

• The scan control PWB has been replaced.

• The EEPROM on the scan control PWB has been replaced.

• The scanner (reading) section has been disassembled. 

• The scanner (reading) unit has been replaced. 

• U2 trouble has occurred.

(Adjustment mode selection)

1) Go through the modes specified in Simulation 50-12.

2) Using the numeric keypad, select the adjustment item PLATEN,

which is intended to adjust the off-center in original table mode. 

3) Press the Start key

Measure the void area dimensions in the front and rear frame
directions, and make sure that the difference between the two
dimensions is within ±1.5 mm.

1

ADJ 7B

Adjust the scanned image off-center in 
original table mode (scan section)

Select 2, and 
press [START] key.

Press [START] key, or 
press [CUSTOM SETTINGS] key.

Item

Set range

Default

0 TRAY SELECT

Paper feed tray 
selection

1 - 6

–

1 COPY START

Copy START (Default)

–

–

2 MAGNIFICATION Print magnification ratio

25 - 400%

100

(Off-center adjustment value)

3 PLATEN

OC mode adjustment

0 - 99

50

4 SPF SIDE1

SPF front surface 
adjustment

5 SPF SIDE2

SPF back surface 
adjustment

50

1

2

Select 1, 
and press 
[START] key.

Press [CUSTOM SETTINGS] key.

Press [START] key.

Press [CUSTOM SETTINGS] key, 
or terminate copying.

Select 0, and press [START] key.

Press [START] key or 
press [CUSTOM SETTINGS] key.

SIMULATION 50-12

ORIGINAL OFF-CENTER ADJUSTMENT. SELECT 0-9, AND PRESS

START.

0.TRAY SELECT 

1

   1.COPY START

2.MAGNIFICATION 

100

(ADJUSTMENT DATA)

3.PLATEN 

50

 4.SPF SIDE1 

50

 5.SPF SIDE2 

50

SIMULATION 50-12

ORIGINAL OFF-CENTER ADJUSTMENT. NOW COPYING.

SIMULATION 50-12

ORIGINAL OFF-CENTER ADJUSTMENT. INPUT VALUE 0-99, AND

PRESS START.

3.PLATEN

SIMULATION 50-12

ORIGINAL OFF-CENTER ADJUSTMENT. SELECT 1-16, AND PRESS

START.

(FEED TRAY)

   1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4

   5.BPT   6.LCC

   (ABOVE+10: DUPLEX MODE)

Select other than 0 - 2, and press [START] key.

100

SIMULATION 50-12

ORIGINAL OFF-CENTER ADJUSTMENT.

(MAGNIFICATION)

  INPUT 25-400(%)

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Reviews:

No comments