manualshive.com logo in svg

Sharp AR-M550N, Service Manual, Page: 342 / 460

Share
Download
Sharp AR-M550N Service Manual Download Page 342

: Feb. 9 2004

1

AR-M550/M620/M700  SIMULATION  8 - 84

Operation/Procedure

Touch the four cross marks (+) sequentially. The coordinates of
pressed positions are set.

When the coordinates setting is completed normally, the display turns
gray. When all the four points are set, the display returns to the normal
state.

Operation/Procedure

When the touch panel is touched, the X and Y coordinate values of the
touched point and the coordinate values of the specified point are dis-
played. The coordinate values set with SIM 65-1 are used as the refer-
ence.

Operation/Procedure

Setting of soft switches other than SW1 can be changed and checked. 

1) Enter the soft switch number to be checked or changed with 10-

key.

The current set state is displayed.

2) Enter the number corresponding to the bit to be changed with 10-

key.

(Example) When the bit of 5 is to be changed, enter 5.

The set value of 1/0 is alternatively changed every time when the
target key is pressed.

3) After completion of setting of all the bits, press [START] key.

Operation/Procedure

1) Set the destination code with 10-key.

The codes other than the above are recognized as Japan.

2) Press [START] key.

3) The confirmation menu of YES/NO of clear is displayed. Select

one.

4) Press [START] key. 

The soft switch (except for the adjustment values) is cleared according
to the destination selected in procedure 1).

NOTE: When the FAX BOX is not installed, initialization including the

adjustment value is performed. (The adjustment value is stored
in the FAX BOX.)

65

65-1

Purpose

Adjustment

Function
(Purpose)

Used to adjust the touch panel (LCD display section) 
detection position.

Section

Operation (Display/Operation key)

Item

65-2

Purpose

Adjustment/Setup/Operation data output/Check 
(Display/Print)

Function
(Purpose)

Used to check the result of the touch panel (LCD 
display) detection position adjustment. (The 
coordinates are displayed.)

Section

Operation (Display/Operation key)

Item

66

66-1

Purpose

Setting

Function
(Purpose)

Used to change and check the FAX soft switch 
functions. (Used to change and check the functions 
provided for the FAX soft switches.)

Section

FAX

Item

SIMULATION 65-1

SIMULATION 65-2

400

500

600

40

100            200            300

100

140

600

180

200

Press [START] key.

Press [CUSTOM SETTINGS] key or [START] key.

66-2

Purpose

Data clear

Function
(Purpose)

Used to clear the FAX soft switch function data and to 
set to the default. (Excluding the adjustment values.)

Section

FAX

Item

Data

Japan

0 0 0 0 0 0 0 0

Finland

0 0 1 1 1 1 0 0

U.S.A.

1 0 1 1 0 1 0 1

Norway

1 0 0 0 0 0 1 0

Australia

0 0 0 0 1 0 0 1

Denmark

0 0 1 1 0 0 0 1

U.K.

1 0 1 1 0 1 0 0

Netherlands

0 1 1 1 1 0 1 1

France

0 0 1 1 1 1 0 1

Italy

0 1 0 1 1 0 0 1

Germany

0 0 0 0 0 1 0 0

Switzerland

1 0 1 0 0 1 1 0

Sweden

1 0 1 0 0 1 0 1

Austria

0 0 0 0 1 0 1 0

Newzealand

0 1 1 1 1 1 1 0

Indonesia

0 1 0 1 0 1 0 0

China

0 0 1 0 0 1 1 0

Thailand

1 0 0 1 0 0 1

Singapore

1 0 0 1 1 1 0 0

Malaysia

0 1 1 0 1 1 0 0 

TW

1 1 1 1 1 1 1 0

India

0 1 0 1 0 0 1 1

Other1

1 1 1 1 1 1 0 1

Philippines

1 0 0 0 1 0 0 1

Other2

1 1 1 1 1 1 0 0

Hongkong

0 1 0 1 0 0 0 0

Ohter3

1 1 1 1 1 0 1 1

1

YES

FAX soft SW is cleared.

2

NO

Not cleared.

SIMULATION 66-1

FAX SOFT SW. SETTING. SELECT 2-120, AND PRESS START.

SIMULATION 66-1

FAX SOFT SW. SETTING. INPUT DATA No(1-8), AND PRESS

START.

     OFT SW-2:

1  2  3  4  5  6  7  8

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Reviews:

No comments