manualshive.com logo in svg

Sharp AR-M550N, Service Manual, Page: 295 / 460

Share
Download
Sharp AR-M550N Service Manual Download Page 295

: Feb. 9 2004

1

AR-M550/M620/M700  SIMULATION  8 - 37

Operation/Procedure

1) Select the counter to be cleared with 10-key. 

2) Press [START] key. 

The confirmation to clear is opened. 

3) Select Yes/NO of counter clear with 10-key. 

YES: Clear

NO: Not clear

4) Press [START] key.

* = PAPER JAM, SPF JAM, TROUBLE

Operation/Procedure

1) Select the counter to be cleared with 10-key.

2) Press [START] key. 

The confirmation to clear is opened. 

3) Select Yes/NO of counter clear with 10-key. 

YES: Clear

NO: Not clear

4) Press [START] key.

* = TRAY1,  TRAY2, TRAY3, TRAY4, BPT, ADU, LCC

0

TRAY SELECT

　

AUTO ONLY

Auto only (No selection 
allowed)

1

PRINT START

Print execution
Print of the set data is 
executed.

2

PRINT PATTERN

Print pattern
1. Paper transport time data

24

24-1

Purpose

Data clear

Function
(Purpose)

Used to clear the misfeed counter, the misfeed history, 
the trouble counter, and the trouble history. (The 
counters are cleared after completion of maintenance.)

Section

Item

Counter

1

PAPER JAM

Number of paper jams

2

SPF JAM

Number of SPF jams

3

TROUBLE

Number of troubles

1

1

SIMULATION 23-80

DATA PRINT MODE. SELECT SETTING, AND PRESS START.

0. TRAY SELECT  :AUTO ONLY

1. PRINT START

2. PRINT PATTERN:

1

1

SIMULATION 23-80

0

SIMULATION 23-80

DATA PRINT MODE. EXECUTING....

0. TRAY SELECT  :

1

Select 1 and 
press [START] key.

Press [CUSTOM SETTING] key 
or [START] key. 

Press [CUSTOM SETTING] key 
or [START] key.

Select 2 and press [START] key. 

DATA PRINT MODE.

INPUT VALUE, AND PRESS START.

(PRINT PATTERN)

INPUT 1.

1

Press [START] key.

Press [CUSTOM SETTINGS] key or [START] key.

24-2

Purpose

Data clear

Function
(Purpose)

Used to clear the number of use (the number of prints) 
of each paper feed section.

Section

Paper feed

Item

Counter

1

TRAY1

Tray 1 use quantity

2

TRAY2

Tray 2 use quantity

3

TRAY3

Tray 3 use quantity

4

TRAY4

Tray 4 use quantity

5

BPT

Manual feed tray use quantity

6

ADU

Duplex feed quantity

7

LCC

Side LCC use quantity

Press [START] key.

Press [CUSTOM SETTINGS] key or [START] key. 

SIMULATION 24-1

JAM/ TROUBLE COUNTER DATA CLEAR. SELECT1-3, AND

PRESS START.

1. PAPER JAM

2. SPF JAM

3. TROUBLE

1

SIMULATION 24-1

* COUNTER DATA CLEAR.

ARE YOU SURE?

1. YES

2. NO

1

1

SIMULATION 24-2

PAPER FEED COUNTER DATA CLEAR. SELECT1-6, AND PRESS

START.

1. TRAY1    2. TRAY2

3. TRAY3    4. TRAY4

5. BPT      6. ADU

7. LCC

SIMULATION 24-2

* COUNTER DATA CLEAR.

ARE YOU SURE?

1. YES

2. NO

1

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Reviews:

No comments